В общем, СПАСАЙТЕ!!!При сборке linux-2.6.38-rc4
make menuconfig [...Serial ATA and Parallel ATA drivers, SCSI, RAID... всё включено]
make all && make modules_install && make install
всё проходит без ошибок...
mkinitrd --preload="scsi_mod sd_mod libata ahci ehci-hcd ohci-hcd uhci-hcd jbd ext3 ata_piix" /boot/initrd-2.6.38-rc4-ahci.img 2.6.38-rc4
тоже всё отлично...при перезагрузке KERNEL PANIC!
Не видит корневой раздел, SATA (режим AHCI)Завтра сдавать в датацентр... Хана...
p.s. Буду благодарен за помощь (возможны призы*), я думаю, что косяк с драйверами и контроллером, но где копать?!
На ядре 2.6.18 грузится в AHCI, так что с железом проблем нет!Далее некоторые технические подробности...
Мать: Intel SE7230NH1-E
[root@kraft1u /]# lspci
00:00.0 Host bridge: Intel Corporation E7230/3000/3010 Memory Controller Hub
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01)
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01)
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01)
00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 01)
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01)
01:00.0 PCI bridge: Intel Corporation 6702PXH PCI Express-to-PCI Bridge A (rev 09)
04:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
04:00.4 IPMI SMIC interface: Intel Corporation 82573E KCS (Active Management) (rev 03)
05:04.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)
05:05.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
Вывод на старом ядре:[root@kraft1u /]# uname -a
Linux kraft1u 2.6.18-194.32.1.el5 #1 SMP Wed Jan 5 17:53:09 EST 2011 i686 i686 i386 GNU/Linux[root@kraft1u /]# dmesg
Linux version 2.6.18-194.32.1.el5 (mockbuild@builder10.centos.org) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Wed Jan 5 17:53:09 EST 2011
BIOS-provided physical RAM map:
BIOS-e820: 0000000000010000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dfe67000 (usable)
BIOS-e820: 00000000dfe67000 - 00000000dfee9000 (ACPI NVS)
BIOS-e820: 00000000dfee9000 - 00000000dfeed000 (usable)
BIOS-e820: 00000000dfeed000 - 00000000dfeff000 (ACPI data)
BIOS-e820: 00000000dfeff000 - 00000000dff00000 (usable)
BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Warning only 4GB will be used.
Use a PAE enabled kernel.
3200MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fec60
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 1048576
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 819200 pages, LIFO batch:31
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 INTEL ) @ 0x000fe020
ACPI: RSDT (v001 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0xdfefde48
ACPI: FADT (v001 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0xdfefcf10
ACPI: MADT (v001 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0xdfefce10
ACPI: WDDT (v001 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0xdfef7f90
ACPI: MCFG (v001 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0xdfef7f10
ACPI: ASF! (v032 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0xdfefcd10
ACPI: HPET (v001 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0xdfef7e90
ACPI: SSDT (v001 INTEL CpuPm 0x0000053c MSFT 0x01000013) @ 0xdfefdc10
ACPI: SSDT (v001 INTEL Cpu0Ist 0x0000053c MSFT 0x01000013) @ 0xdfefda10
ACPI: SSDT (v001 INTEL Cpu1Ist 0x0000053c MSFT 0x01000013) @ 0xdfefd810
ACPI: SSDT (v001 INTEL Cpu2Ist 0x0000053c MSFT 0x01000013) @ 0xdfefd610
ACPI: SSDT (v001 INTEL Cpu3Ist 0x0000053c MSFT 0x01000013) @ 0xdfefd410
ACPI: DSDT (v001 INTEL 04DT044 0x0000053c MSFT 0x01000013) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:6 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:6 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 5, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x06] address[0xfec10000] gsi_base[30])
IOAPIC[1]: apic_id 6, version 32, address 0xfec10000, GSI 30-53
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 2 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at e0000000 (gap: dff00000:20100000)
Detected 2793.114 MHz processor.
Built 1 zonelists. Total pages: 1048576
Kernel command line: ro root=LABEL=/ rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec10000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0769000 soft=c0749000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3626664k/4194304k available (2180k kernel code, 40392k reserved, 910k data, 228k init, 2750896k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 5586.22 BogoMIPS (lpj=2793114)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000180 0000e49d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 11000
CPU 1 irqstacks, hard=c076a000 soft=c074a000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5586.09 BogoMIPS (lpj=2793049)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e49d 00000000 00000001
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000180 0000e49d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) D CPU 2.80GHz stepping 04
Total of 2 processors activated (11172.32 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Using local APIC timer interrupts.
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=340 bytes
sizeof(dentry)=136 bytes
sizeof(ext3inode)=492 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=176 bytes
migration_cost=531
checking if image is initramfs... it is
Freeing initrd memory: 2537k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: PXH quirk detected, disabling MSI for SHPC device
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0.PXS1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
pnp: 00:01: iomem range 0xfed13000-0xfed13fff has been reserved
pnp: 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
pnp: 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
pnp: 00:06: ioport range 0x500-0x53f has been reserved
pnp: 00:06: ioport range 0x400-0x47f could not be reserved
pnp: 00:06: ioport range 0x680-0x6ff has been reserved
PCI: Bridge: 0000:01:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: 2000-0000
MEM window: e8100000-00000000
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: 1000-0000
MEM window: e8000000-00000000
PREFETCH window 0x00000000e0000000-0x00000000e7ffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:01:00.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5 -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
type=2000 audit(1297691094.761:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
- Added public key 59F555817D939EA9
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:05:04.0
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1c.4 to 64
PCI: Setting latency timer of device 0000:00:1c.5 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 217
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x30b0-0x30b7, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
Probing IDE interface ide0...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Initalizing network drop monitor service
Freeing unused kernel memory: 228k freed
Write protecting the kernel read-only data: 410k
Time: tsc clocksource has been installed.
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 19 (level, low) -> IRQ 225
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xe8200000 port 0xe8200100 irq 233
ata2: SATA max UDMA/133 abar m1024@0xe8200000 port 0xe8200180 irq 233
ata3: SATA max UDMA/133 abar m1024@0xe8200000 port 0xe8200200 irq 233
ata4: SATA max UDMA/133 abar m1024@0xe8200000 port 0xe8200280 irq 233
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: HDT722516DLA380, V43OA9BA, max UDMA/133
ata1.00: 321672960 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-8: ST3500418AS, CC46, max UDMA/133
ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-8: ST3500418AS, CC46, max UDMA/133
ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
Vendor: ATA Model: HDT722516DLA380 Rev: V43O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 321672960 512-byte hdwr sectors (164697 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: ST3500418AS Rev: CC46
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1
sd 2:0:0:0: Attached scsi disk sdb
Vendor: ATA Model: ST3500418AS Rev: CC46
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: sdc1
sd 3:0:0:0: Attached scsi disk sdc
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 50, io mem 0xe8200400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 50, io base 0x00003080
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 225, io base 0x00003060
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 217, io base 0x00003040
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 177, io base 0x00003020
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel@redhat.com
device-mapper: dm-raid45: initialized v0.2594l
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 3 users, 6 roles, 1951 types, 257 bools, 1 sens, 1024 cats
security: 61 classes, 77102 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sda2, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1297691120.597:2): policy loaded auid=4294967295 ses=4294967295
EDAC MC: Ver: 2.0.1 Jan 5 2011
EDAC MC0: Giving out device to i3000_edac i3000: DEV 0000:00:00.0
input: PC Speaker as /class/input/input0
ACPI: PCI Interrupt 0000:00:1f.3 -> GSI 19 (level, low) -> IRQ 225
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k3.1
e1000e: Copyright (c) 1999-2008 Intel Corporation.
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:04:00.0 to 64
eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:83:2b:b6
eth0: Intel(R) PRO/1000 Network Connection
eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff
Intel(R) PRO/1000 Network Driver - version 7.3.21-k4.1-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 17 (level, low) -> IRQ 169
intel_rng: Firmware space is locked read-only. If you can't or
intel_rng: don't want to disable this in firmware setup, and if
intel_rng: you are certain that your system has a functional
intel_rng: RNG, try using the 'no_fwh_detect' option.
e1000: 0000:05:05.0: e1000_probe: (PCI:33MHz:32-bit) 00:16:76:83:2b:b7
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 3:0:0:0: Attached scsi generic sg2 type 0
floppy0: no floppy controllers found
lp: driver loaded but no devices found
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Mapper loaded
dell-wmi: No known WMI GUID found
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdc1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: created md0
md: bind<sdb1>
md: bind<sdc1>
md: running: <sdc1><sdb1>
md: raid1 personality registered for level 1
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda2, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
EXT4-fs (dm-0): mounted filesystem with ordered data mode
SELinux: initialized (dev dm-0, type ext4), uses xattr
Adding 7132852k swap on /dev/sda3. Priority:-1 extents:1 across:7132852k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
Loading iSCSI transport class v2.0-871.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
cxgb3i: tag itt 0x1fff, 13 bits, age 0xf, 4 bits.
iscsi: registered transport (cxgb3i)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
Broadcom NetXtreme II CNIC Driver cnic v2.1.0 (Oct 10, 2009)
Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.0 (Dec 06, 2009)
iscsi: registered transport (bnx2i)
iscsi: registered transport (tcp)
iscsi: registered transport (iser)
iscsi: registered transport (be2iscsi)
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 228 bytes per conntrack
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
eth0: no IPv6 routers present
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
попробуйCONFIG_SYSFS=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
> попробуй
> CONFIG_SYSFS=y
> CONFIG_SYSFS_DEPRECATED=y
> CONFIG_SYSFS_DEPRECATED_V2=yПопробую. А пока МКАД, ПРОБКИ ПРОБКИ ПРОБКИ ПРОБКИ ПРОБКИ ПРОБКИ
> попробуй
> CONFIG_SYSFS=y
> CONFIG_SYSFS_DEPRECATED=y
> CONFIG_SYSFS_DEPRECATED_V2=y**************************
* ВАРИАНТ РАБОТАЕТ! *
**************************Уважаемый "aaaaaaaaaaaaa", благодарю Вас за помощь!
*как приз (см. выше), могу предоставить $бесплатно (1GB+PHP+MySQL) или Beer или ещё что нибудь или раритерный винт SCSI 50pin от APPLE или какую нибудь железку {%список%};
иначе ничего; done ))
exit 0Тема закрыта!
Распакуйте свой initrd и посмотрите, что там
> Распакуйте свой initrd и посмотрите, что тамПервым делом распаковал, в init и lib всё присутствует
> При сборке linux-2.6.38-rc4
> make menuconfig [...Serial ATA and Parallel ATA drivers, SCSI, RAID... всё включено]-
> make all && make modules_install && make install
> всё проходит без ошибок...
> mkinitrd --preload="scsi_mod sd_mod libata ahci ehci-hcd ohci-hcd uhci-hcd jbd ext3 ata_piix"
> /boot/initrd-2.6.38-rc4-ahci.img 2.6.38-rc4
> тоже всё отлично...-
> при перезагрузке KERNEL PANIC!
> Не видит корневой раздел, SATA (режим AHCI)-
> Завтра сдавать в датацентр... Хана...-
-
ручная сборка ядра и инитрд? Чем-то серьезно обосновано ? Скорее всего - ССЗБ.
>[оверквотинг удален]
>> тоже всё отлично...
> -
>> при перезагрузке KERNEL PANIC!
>> Не видит корневой раздел, SATA (режим AHCI)
> -
>> Завтра сдавать в датацентр... Хана...
> -
> -
> ручная сборка ядра и инитрд? Чем-то серьезно обосновано ? Скорее всего -
> ССЗБ.Всё дело в хитрых ловушках (httpd + nginx + iptables и на ssh фишка с анти-брутфорсом)
Мне кажется особенности в контроллере материнки...Так бы сам с удовольствием юзал всё что есть, если бы логи не читал (от которых волосы дыбом) 8)))))
p.s. ещё postfix (корпоративный) в довесок с толпой пользователей)))
>> ручная сборка ядра и инитрд? Чем-то серьезно обосновано ? Скорее всего -
>> ССЗБ.
> Всё дело в хитрых ловушках (httpd + nginx + iptables и на
> ssh фишка с анти-брутфорсом)Поподробнее, что из этого потребовало пересборки ядра ?
>>> ручная сборка ядра и инитрд? Чем-то серьезно обосновано ? Скорее всего -
>>> ССЗБ.
>> Всё дело в хитрых ловушках (httpd + nginx + iptables и на
>> ssh фишка с анти-брутфорсом)
> Поподробнее, что из этого потребовало пересборки ядра ?Для начала оперативка))) В стандартном ядре 4 гигабайта лимит, у меня больше... Модули FTP, TARPIT...
>>>> ручная сборка ядра и инитрд? Чем-то серьезно обосновано ? Скорее всего -
>>>> ССЗБ.
>>> Всё дело в хитрых ловушках (httpd + nginx + iptables и на
>>> ssh фишка с анти-брутфорсом)
>> Поподробнее, что из этого потребовало пересборки ядра ?
> Для начала оперативка))) В стандартном ядре 4 гигабайта лимит, у меня больше...Вот жеж центось какое г-но, даже pae-шные ядра в дистрибутив не кладут.
> Модули FTP, TARPIT...
Ключевое слово тут - _модули_. Разве они требуют патч кода _ядра_ ?
>>>>> ручная сборка ядра и инитрд? Чем-то серьезно обосновано ? Скорее всего -
>>>>> ССЗБ.
>>>> Всё дело в хитрых ловушках (httpd + nginx + iptables и на
>>>> ssh фишка с анти-брутфорсом)
>>> Поподробнее, что из этого потребовало пересборки ядра ?
>> Для начала оперативка))) В стандартном ядре 4 гигабайта лимит, у меня больше...
> Вот жеж центось какое г-но, даже pae-шные ядра в дистрибутив не кладут.
>> Модули FTP, TARPIT...
> Ключевое слово тут - _модули_. Разве они требуют патч кода _ядра_
> ?Я прошу не придираться к моим словам, память модулем mem_up_to_64g.ko не расширяется))) И процессор модулем cpu_xeon.ko то же))) Хотя идея не плохая. Ещё модуль trezviy_sysadmin.ko, который настраивает и мониторит систему 24 часа в сутки и без сна O_o.
Удачи!
========ТЕМА ЗАКРЫТА========