Здравствуйте. Есть Cisco 7206VXR. Никак не могу найти команду speed, чтобы изменить скорость FastEthernet-a на 10Mbps. Нету такой команды в Router(config-if)#. Что же делать? Заранее благодарюFastEthernet0/0 is up, line protocol is up
Hardware is DEC21140A, address is ****.****.**** (bia ****.****.****)
Internet address is xxx.xxx.xxx.xxx/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 2000 bits/sec, 4 packets/sec
5 minute output rate 3000 bits/sec, 4 packets/sec
18738 packets input, 2683395 bytes
Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast
0 input packets with dribble condition detected
18666 packets output, 1445036 bytes, 0 underruns
14 output errors, 0 collisions, 2 interface resets
0 babbles, 0 late collision, 0 deferred
16 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped outОтрывки от show version
IOS (tm) 7200 Software (C7200-IS-M), Version 12.0(5)T1, RELEASE SOFTWARE (fc1)c7200-is-mz.120-5.T1.bin
1 FastEthernet/IEEE 802.3 interface(s)
4 Serial network interface(s)
Может быть bandwidth
>Может быть bandwidthне может быть
>>Может быть bandwidth
>
>не может бытьтогда какая команда спасет меня
на этих интерфейсах и нету такой команды
оно 10мбит просто не умеет!
>на этих интерфейсах и нету такой команды
>оно 10мбит просто не умеет!
No togda, skajhite pojhaluysta, u menya davno bil Cisco 2650XM, s fastethernet interface-om, i na nego ya stavlyal kommandu "speed 10" i vsyo rabotalo normal'no. Mojhet vsye taki eto iz za IOS-a? Mojhet pomenyat' IOS?Zaranee blagodaryu
просто интерфейсы на 26хх это совсем не тоже самое что и на 72/75
на 72/75 просто не умеет, считается, что это не нужно
потому что железка которая сотни тыш пакетов маршрутизирует, через гигабитную шину
не предназначена чтоб 10мбитные концы обслуживать
вот както так
надо 10мбит бери 26/36
Привет,Посмотрите sh ver. Некоторые версии хардуера кошек имеют порты в 10/100 и даже 10/100/1000 (чаще всего на коммутаторах, 3750, к примеру). Другие версии - только 10 (Ethernet), только 100 (FastEthernet) и т.д. По-моему, "помочь" может только замена порта - или провести трафик через какой-нибудь управляемый коммутатор.
WWell,
Ponyal. Ogromnoye spasibo !!!
> Ponyal. Ogromnoye spasibo !!!
да всё работает:
7206#conf t
Enter configuration commands, one per line. End with CNTL/Z.
7206(config)#int f0/0
7206(config-if)#speed ?
10 Force 10 Mbps operation
100 Force 100 Mbps operation
auto Enable AUTO speed configuration7206(config-if)#
>> Ponyal. Ogromnoye spasibo !!!
>да всё работает:
>7206#conf t
>Enter configuration commands, one per line. End with CNTL/Z.
>7206(config)#int f0/0
>7206(config-if)#speed ?
> 10 Force 10 Mbps operation
> 100 Force 100 Mbps operation
> auto Enable AUTO speed configuration
>
>7206(config-if)#
Umenya stoit 7206VXR, f v config-if netu takoy kommandi: speed
Blagodaryu
И У меня такаяже железка 7206VXR,
какой FastEthernet у тебя не понимает speed ? где стоит ?
Что показывает по sh diag ?
пример:
sh diag
Slot 0:
Dual FastEthernet (RJ-45) I/O Card Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 1w6d ago
EEPROM contents at hardware discovery:
Hardware Revision : 2.1
Top Assy. Part Number : 800-00000-06
Part Number : 73-0000-06
Board Revision : B0
PCB Serial Number : 1234567
RMA History : 00
Fab Version : 03
Fab Part Number : 12-3456-78
Product Number : C7200-I/O-2FE/E
Deviation Number : 0-0
EEPROM format version 4на этой плате всё отрабатывает
7206#sh run int f0/1
interface FastEthernet0/1
duplex full
speed 10
no cdp enable
end
http://www.cisco.com/en/US/products/hw/routers/ps341/product...Product Number
Description
C7200-I/O-GE+E
One Gigabit Ethernet and one Ethernet port; equipped with a GBIC receptacle for 1000 megabits per second (Mbps) operation and an RJ-45 receptacle for 10-Mbps operation
C7200-I/O-2FE/E
Two autosensing Ethernet/Fast Ethernet ports; equipped with two RJ-45 receptacles for 10/100-Mbps operation.
C7200-I/O-FE1
One Fast Ethernet port; equipped with an MII receptacle and an RJ-45 receptacle for use at 100 Mbps full-duplex or half-duplex operation. Only one receptacle can be configured for use at a time.
C7200-I/O
Has no Fast Ethernet port.
C7200-I/O-FE-MII2
One Fast Ethernet port; equipped with a single MII receptacle.
Привет ВСЕМ !!!show diag
Fast-ethernet on C7200 I/O card with MII or RJ45 port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time 1w6d ago
EEPROM contents at hardware discovery:
Hardware revision 2.0 Board revision A0
Serial number 12345678 Part number 73-0000-03
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
А теперь, что касается "speed"Router(config)#int fa0/0
Router(config-if)#speed ?
% Unrecognized command
Router(config-if)#speed
Try comm>>>> mode ?>Привет ВСЕМ !!!
>
>show diag
>
>Fast-ethernet on C7200 I/O card with MII or RJ45 port adapter, 1
>port
>Port adapter is analyzed
>Port adapter insertion time 1w6d ago
>EEPROM contents at hardware discovery:
>Hardware revision 2.0
> Board revision A0
>Serial number 12345678
>Part number 73-0000-03
>Test history 0x0
> RMA number
> 00-00-00
>EEPROM format version 1
>
>
>А теперь, что касается "speed"
>
>Router(config)#int fa0/0
>Router(config-if)#speed ?
>% Unrecognized command
>Router(config-if)#speed
Скольео можно мусолить это?
Ну нет там speed 10, и не будет! И вообще она с 2000 EO все!
http://www.cisco.com/en/US/products/hw/routers/ps341/prod_in...