Помогите уважаемые
случайно удалили flash с cisco 3750
при заходе на cisco видим только (все началось с того что не мог залить ios новый - не проходила команда (copy tftp: flash: )!!! )
можно на почту qwer2005@Wmail.ru
switch:
switch:switch: help
? -- Present list of available commands
boot -- Load and boot an executable image
cat -- Concatenate (type) file(s)
copy -- Copy a file
delete -- Delete file(s)
dir -- List files in directories
flash_init -- Initialize flash filesystem(s)
format -- Format a filesystem
fsck -- Check filesystem consistency
help -- Present list of available commands
load_helper -- Load and initialize a helper image
memory -- Present memory heap utilization information
mkdir -- Create dir(s)
more -- Concatenate (display) file(s)
rename -- Rename a file
reset -- Reset the system
rmdir -- Delete empty dir(s)
set -- Set or display environment variables
set_bs -- Set attributes on a boot sector filesystem
set_param -- Set system parameters in flash
sleep -- Pause (sleep) for a specified number of seconds
-- MORE --
trap -- Cause a software breakpoint to occur
type -- Concatenate (type) file(s)
unset -- Unset one or more environment variables
version -- Display boot loader versionswitch:
switch:
///////////////////////////////////////////////////
а до удаление видел вот что см ниже,Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C3750 Software (C3750-I9-M), Version 12.2(20)SE4, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Sun 09-Jan-05 00:09 by antonino
Image text-base: 0x00003000, data-base: 0x0099748CROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.1(14r)EA1a, RELEASE SOFTWARE (fc1)Sw-B uptime is 2 days, 19 hours, 58 minutes
System returned to ROM by power-on
System image file is "flash:c3750-i9-mz.122-20.SE4/c3750-i9-mz.122-20.SE4.bin"cisco WS-C3750-24TS (PowerPC405) processor (revision G0) with 118784K/12280K bytes of memory.
Processor board ID CAT0910K1AT
Last reset from power-on
1 Virtual Ethernet/IEEE 802.3 interface(s)
24 FastEthernet/IEEE 802.3 interface(s)
2 Gigabit Ethernet/IEEE 802.3 interface(s)
The password-recovery mechanism is enabled.512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : 00:13:7F:F9:56:00
Motherboard assembly number : 73-7055-09
Power supply part number : 341-0034-01
Motherboard serial number : CAT0910036J
Power supply serial number : DAB090100NU
Model revision number : G0
Motherboard revision number : A0
Model number : WS-C3750-24TS-S
System serial number : CAT0910K1AT
Hardware Board Revision Number : 0x06
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C3750-24TS 12.2(20)SE4 C3750-I9-M
Configuration register is 0xFSw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#sh flashDirectory of flash:/
3 -rwx 1653 Mar 1 1993 21:43:21 +00:00 config.text
4 -rwx 27 Mar 1 1993 21:43:21 +00:00 private-config.text
5 drwx 192 Mar 1 1993 00:06:16 +00:00 c3750-i9-mz.122-20.SE415998976 bytes total (8245760 bytes free)
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
Sw-B#
http://www.cisco.com/en/US/products/hw/switches/ps607/produc...
пробовал нифига не проходит,
switch:switch:
switch:
switch:
switch:
switch:
switch:
switch:
switch: init?flash
Unknown cmd: init?flashswitch: flash_init
Initializing Flash...
...The flash is already initialized.
Setting console baud rate to 9600...switch:
switch:
switch: load_hekper
Unknown cmd: load_hekperswitch: helper_load
Unknown cmd: helper_loadswitch: dir flash
unable to stat flash/: no such deviceswitch: dir_flash
Unknown cmd: dir_flashswitch: dir_flash:
Unknown cmd: dir_flash:switch:
switch:
switch:
switch:
Base ethernet MAC Address: 00:13:7f:fe:d3:80
Xmodem file system is available.
The password-recovery mechanism is enabled.
Initializing Flash...
flashfs[0]: 0 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 1024
flashfs[0]: Bytes available: 15997952
flashfs[0]: flashfs fsck took 8 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
done.
Loading "flash:c3750-i9-mz.122-20.SE4/c3750-i9-mz.122-20.SE4.bin"...flash:c3750-i9-mz.122-20.SE4/c3750-i9-mz.122-20.SE4.bin: no such file or directoryError loading "flash:c3750-i9-mz.122-20.SE4/c3750-i9-mz.122-20.SE4.bin"
Interrupt within 5 seconds to abort boot process.
Boot process failed...The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
switch: flash_init
Initializing Flash...
...The flash is already initialized.
Setting console baud rate to 9600...switch: load_helper
switch:
switch:
switch: dir flash:
Directory of flash:/
15997952 bytes available (1024 bytes used)switch:
switch: delete flash:
Are you sure you want to delete "flash:" (y/n)?y
File "flash:" not deleted -- no such file or directoryswitch:
switch:
switch: dir flash:
Unknown cmd: dirswitch:
switch:
swimkdir:
Unknown cmd: copymkdir:switch: mkdir:
Unknown cmd: mkdir:switch: mkdir: flash:
Unknown cmd: mkdir:switch:
>пробовал нифига не проходит,не понятно _что_ Вы побовали. Из лога видно только попытки ввода неправильных комманд (зачем это постить в форум не понятно).
Перечитайте страницу по ссылке. Там вполне понятно английскими буквами по монитору написано что делать.
В частности:
Copy the image to the Flash using HyperTerminal for Microsoft Windows, or another terminal software program. The command on the switch is copy xmodem: flash:filename , where filename is the name of file that you downloaded. With HyperTerminal, use the TRANSFER -- SEND FILE option using the XMODEM protocol. Start the XMODEM download within three seconds. Otherwise, the switch times out the XMODEM copy.When the XMODEM request appears, issue the appropriate command on the terminal-emulation software to start the transfer. Copy the software image into Flash memory. The command to issue is switch: copy xmodem: flash:image_filename .
даже copy xmodem: flash: (файл.bin )не проходит
а не надо создавать какую нидь директорию??пишет ошибка на I/O error
а когда начинаю что нидь передавть то вообще стоит вижу окошко пустое что никаких пакетов никуда не передаеитться....
хех
достал со клада ws-3750-48ts-sswitch: flash_init
Initializing Flash...
flashfs[0]: 3 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7962624
flashfs[0]: Bytes available: 8036352
flashfs[0]: flashfs fsck took 9 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
Setting console baud rate to 9600...switch: load_helper
switch: copy xmodem: flash:111
Begin the Xmodem or Xmodem-1K transfer now...
CCC
Starting xmodem transfer. Press Ctrl+C to cancel.
Transferring 123...
100% 3 bytes 3 bytes/s 00:00:01 0 Errors.
File "xmodem:" successfully copied to "flash:111"---CUT---
Switch>en
Switch#sh flash:Directory of flash:/
2 -rwx 7958174 Mar 1 1993 00:07:52 +00:00 c3750-ipservicesk9-mz.122-25.SEE.bin
3 -rwx 2105 Mar 1 1993 00:01:57 +00:00 config.text
4 -rwx 24 Mar 1 1993 00:01:57 +00:00 private-config.text
5 -rwx 128 Jan 1 1970 00:01:30 +00:00 111Так что что-то Вы делаете не так.
Хинт:
Сначала copy xmodem: flash:имя_файла на каталисте
и только затем инициируем передачу в терминал-клиенте
что-то Вы делаете не так.
>
>Хинт:
>Сначала copy xmodem: flash:имя_файла на каталисте
>и только затем инициируем передачу в терминал-клиенте/.....................
когда делаю так как вы рекомендуете(спаибо большое вам за это!!)
надеюсь я вас еще не разозлил.... :-))вот что имеем или ругаеться что bad file name или no such device
???
ПОЛУЧИЛОСЬ йоооо!!!!!!!!!!!!!!!!!!!!!!!!1111брат спасибки за участие
а сделали вот как,при переливании IOS в формате ***.bin он нихрена не давал переливаться
а когда я начал заливать файл ***.tar он млин пошел
почему так не понятно !??????но главное процесс пошел
спасибо за помощь Ракис............!!!!! респект
>спасибо за помощь Ракис............!!!!! респектпожалуйста. рад что удалось помоч
> при переливании IOS в формате ***.bin он нихрена не давал
> переливаться
> а когда я начал заливать файл ***.tar он млин пошелА как вы потом его распаковывали?
Base ethernet MAC Address: 00:1c:f9:c4:83:00
Xmodem file system is available.
The password-recovery mechanism is enabled.The system has been interrupted prior to initializing the
flash filesystem. The following commands will initialize
the flash filesystem, and finish loading the operating
system software:flash_init
load_helper
boot
switch: flash_init
Initializing Flash...
flashfs[0]: 600 files, 19 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 7718912
flashfs[0]: Bytes available: 24795136
flashfs[0]: flashfs fsck took 10 seconds.
...done Initializing Flash.
Boot Sector Filesystem (bs) installed, fsid: 3
Setting console baud rate to 9600...switch: load_helper
switch: dir flash
unable to stat flash/: no such deviceswitch:
switch: dirList of filesystems currently registered:
flash[0]: (read-write)
xmodem[1]: (read-only)
null[2]: (read-write)
bs[3]: (read-only)у меня задача сбросить пароль.
т.е. в каталоге flash переименовать конфиг, что бы каталист загрузился с дефолтовыми настройкамикаталист 2960
http://www.cisco.com/en/US/products/hw/switches/ps628/produc...