Добрый день!
Есть Cisco UC500, факс включён в FXS порт. Необходимо назначить данному порту внутренний номер и привязать его к городскому номеру. В telephony-service уже включил auto-reg-ephone и ephone-reg. Подскажите какие команды помогу осуществить желаемое ?

Часть running-config:
!
voice translation-rule 1
rule 1 /306/ /306/
rule 2 /305/ /305/
!
...
!
voice translation-rule 410
rule 1 /306/ /306/
rule 2 /305/ /305/
rule 3 /^9\(.*\)/ /\1/
rule 4 /^...$/ /305/
!

• Настройка FXS порта,XyligaN, 12:33 , 08-Окт-08

Настроил ephone, ephone-dn,dial-peer...всё-равно при выводе статус UNREGISTERED.

show stcapp device summary
Total Devices:           4
Total Calls in Progress: 0
Total Call Legs in Use:  0

Port       Device          Device   Call          Dev     Directory   Dev
Identifier Name            State    State         Type    Number      Cntl
---------- --------------- -------- ------------- -------    ----------- ----
0/0/0      AN1B8FAB7A40000 OOS      UNREGISTERED   ALG                UNKN
0/0/1      AN1B8FAB7A40001 OOS      UNREGISTERED   ALG                UNKN
0/0/2      AN1B8FAB7A40002 OOS      UNREGISTERED   ALG                UNKN
0/0/3      AN1B8FAB7A40003 OOS      UNREGISTERED   ALG                UNKN

show voice port summary
                                          IN       OUT
PORT           CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
============== == ============ ===== ==== ======== ======== ==
0/0/0          --  fxs-ls      up    dorm on-hook  idle     y
0/0/1          --  fxs-ls      up    dorm on-hook  idle     y
0/0/2          --  fxs-ls      up    dorm on-hook  idle     y
0/0/3          --  fxs-ls      up    dorm on-hook  idle     y

show voice port 0/0/0 (где воткнут Fax)

Foreign Exchange Station 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
Type of VoicePort is FXS  VIC3-4FXS/DID
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Supervisory Disconnect Time Out is set to 750 ms
Ringing Time Out is set to infinity
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for US

Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None

Caller ID Info Follows:
Standard BELLCORE
Output attenuation is set to 14 dB
Caller ID is transmitted after 1 ring(s)
Translation profile (Incoming):
Translation profile (Outgoing):

Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Hookflash-in Timing is set to max=1000 ms, min=150 ms
Hookflash-out Timing is set to 400 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [20 40] * 100 msec
Ringer Equivalence Number is set to 1