Не могу настроить эту железку на соединение с E1 от прова.
Итак настройки:card type e1 2
isdn switch-type primary-net5
controller E1 2/0
pri-group timeslots 1-30
interface Serial2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
no cdp enable
У меня вопрос, почему я не вижу voice-port s2/0:1 ?CCME(config)#voice-port ?
<3-50> Voice interface slot #
Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)Другой ИОС пробовал, ничего не изменилось! Чего еще не хватает!?
Вот еще:CCME#sh controllers e1 2/0 br
E1 2/0 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Framing is CRC4, Line Code is HDB3, Clock Source is Line.
Module type is Channelized E1/T1 PRI
Version info Firmware: 0000001D, FPGA: C
Hardware revision is 0.0 , Software revision is 29
Protocol revision is 1
number of CLI resets is 0
receive remote alarm : 0,
transmit remote alarm : 0,
receive AIS alarm : 0,
transmit AIS alarm : 0,
loss of frame : 0,
loss of signal : 0,
Loopback test : 0,
transmit AIS in TS 16 : 0,
receive LOMF alarm : 0,
transmit LOMF alarm : 0,
MIB data updated every 10 seconds.
Data in current interval (832 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 2 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 6 Unavail SecsCCME#sh int s2/0:15
Serial2/0:15 is up, line protocol is up (spoofing)
Hardware is DSX1
MTU 1500 bytes, BW 64 Kbit/sec, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Last input 00:00:05, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 48 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
475 packets input, 1905 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
475 packets output, 1905 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
1 carrier transitions
Timeslot(s) Used:16, Transmitter delay is 0 flagsCCME#sh ip int br
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 10.1.3.254 YES NVRAM up up
GigabitEthernet0/1 unassigned YES TFTP administratively down down
In1/0 192.168.1.5 YES TFTP administratively down down
Serial2/0:0 unassigned YES unset down down
Serial2/0:1 unassigned YES unset down down
Serial2/0:2 unassigned YES unset down down
Serial2/0:3 unassigned YES unset down down
Serial2/0:4 unassigned YES unset down down
Serial2/0:5 unassigned YES unset down down
Serial2/0:6 unassigned YES unset down down
Serial2/0:7 unassigned YES unset down down
Serial2/0:8 unassigned YES unset down down
Serial2/0:9 unassigned YES unset down down
Serial2/0:10 unassigned YES unset down down
Serial2/0:11 unassigned YES unset down down
Serial2/0:12 unassigned YES unset down down
Serial2/0:13 unassigned YES unset down down
Serial2/0:14 unassigned YES unset down down
Serial2/0:15 unassigned YES TFTP up up
Serial2/0:16 unassigned YES unset down down
Serial2/0:17 unassigned YES unset down down
Serial2/0:18 unassigned YES unset down down
Serial2/0:19 unassigned YES unset down down
Serial2/0:20 unassigned YES unset down down
Serial2/0:21 unassigned YES unset down down
Serial2/0:22 unassigned YES unset down down
Serial2/0:23 unassigned YES unset down down
Serial2/0:24 unassigned YES unset down down
Serial2/0:25 unassigned YES unset down down
Serial2/0:26 unassigned YES unset down down
Serial2/0:27 unassigned YES unset down down
Serial2/0:28 unassigned YES unset down down
Serial2/0:29 unassigned YES unset down down
NVI0 10.1.3.254 YES unset up up
Tunnel0 172.16.2.2 YES NVRAM up upВ чем может быть проблема!? Интерфейсы 1-15,17-30 должны быть в апе? куда копать!?
>У меня вопрос, почему я не вижу voice-port s2/0:1 ?Потому что карта nm-1ce1t1-pri умеет терминировать только данные и dialup (при наличие PVDM2-xxDM). Для приема телефонии вам нужен VWIC + PVDM2 или NM-HDV2.
Если вы не хотите принимать телефонию, тогда непонятно зачем вам нужен voice-port.