URL: https://www.opennet.me/cgi-bin/openforum/vsluhboard.cgi
Форум: vsluhforumID6
Нить номер: 21638
[ Назад ]
Исходное сообщение
"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 22-Сен-10 08:34 
Здравствуйте.
Ситуация такая: имеется маршрутизатор Cisco 1721, на единственый ethernet порт, которого подцеплен коммутатор Moxa 508. Коммутатор разбит на 3 влана (основной, резервный каналы + местная сеть) и один порт как транковый влан. На маршрутизаторе поднят OSPF, однако маршруты к нему не приходят, т.е. в sh ip route видны только directly connected сети.
Искал в интернете, и где то натыкался на вскользь упоминаемую фразу, что 1700 не умеют маршрутизировать динамически именно из вланов, т.е. если несколько интерфейсов на самом маррутизере, то пожалуйста, а из вланов не будет. Так ли это? Если нет, то какие могут быть еще причины?
Содержание
Сообщения в этом обсуждении
"Не работает динамическая маршрутизация на 1700"
Отправлено sh_ , 22-Сен-10 10:14 
Покажите sh ip ospf nei и sh ip ospf int
"Не работает динамическая маршрутизация на 1700"
Отправлено Ivan Pomidorov , 22-Сен-10 11:45 
m17#sh ip proto
Routing Protocol is "ospf 1"
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Router ID 172.30.252.193
  Number of areas in this router is 1. 1 normal 0 stub 0 nssa
  Maximum path: 4
  Routing for Networks:
    172.30.252.192 0.0.0.31 area 0
    172.30.252.224 0.0.0.7 area 0
    172.30.252.232 0.0.0.7 area 0
  Routing Information Sources:
    Gateway         Distance      Last Update
    172.30.252.193       110      02:09:11
  Distance: (default is 110)

m17#sh ip ospf nei

m17
#sh ip ospf int
FastEthernet0.4 is up, line protocol is up
  Internet Address 172.30.252.236/29, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.236
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:09
  Index 3/3, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)
FastEthernet0.3 is up, line protocol is up
  Internet Address 172.30.252.227/29, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.227
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:05
  Index 2/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)
FastEthernet0.2 is up, line protocol is up
  Internet Address 172.30.252.193/27, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.193
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:02
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)

"Не работает динамическая маршрутизация на 1700"
Отправлено sh_ , 22-Сен-10 12:04 
Покажите вывод дебуга debug ip ospf hell
"Не работает динамическая маршрутизация на 1700"
Отправлено Ivan Pomidorov , 22-Сен-10 12:05 
m17#sh ip proto
Routing Protocol is "ospf 1"
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Router ID 172.30.252.193
  Number of areas in this router is 1. 1 normal 0 stub 0 nssa
  Maximum path: 4
  Routing for Networks:
    172.30.252.192 0.0.0.31 area 0
    172.30.252.224 0.0.0.7 area 0
    172.30.252.232 0.0.0.7 area 0
  Routing Information Sources:
    Gateway         Distance      Last Update
    172.30.252.193       110      02:09:11
  Distance: (default is 110)

m17#sh ip ospf nei

m17
#sh ip ospf int
FastEthernet0.4 is up, line protocol is up
  Internet Address 172.30.252.236/29, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.236
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:09
  Index 3/3, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)
FastEthernet0.3 is up, line protocol is up
  Internet Address 172.30.252.227/29, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.227
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:05
  Index 2/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)
FastEthernet0.2 is up, line protocol is up
  Internet Address 172.30.252.193/27, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.193
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:02
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 22-Сен-10 12:24 
m17#sh ip proto
Routing Protocol is "ospf 1"
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Router ID 172.30.252.193
  Number of areas in this router is 1. 1 normal 0 stub 0 nssa
  Maximum path: 4
  Routing for Networks:
    172.30.252.192 0.0.0.31 area 0
    172.30.252.224 0.0.0.7 area 0
    172.30.252.232 0.0.0.7 area 0
  Routing Information Sources:
    Gateway         Distance      Last Update
    172.30.252.193       110      02:09:11
  Distance: (default is 110)

m17#sh ip ospf nei

m17
#sh ip ospf int
FastEthernet0.4 is up, line protocol is up
  Internet Address 172.30.252.236/29, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.236
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:09
  Index 3/3, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)
FastEthernet0.3 is up, line protocol is up
  Internet Address 172.30.252.227/29, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.227
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:05
  Index 2/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)
FastEthernet0.2 is up, line protocol is up
  Internet Address 172.30.252.193/27, Area 0
  Process ID 1, Router ID 172.30.252.193, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 172.30.252.193, Interface address 172.30.252.193
  No backup designated router on this network
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:02
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 0, maximum is 0
  Last flood scan time is 0 msec, maximum is 0 msec
  Neighbor Count is 0, Adjacent neighbor count is 0
  Suppress hello for 0 neighbor(s)

"Не работает динамическая маршрутизация на 1700"
Отправлено lumenous , 22-Сен-10 13:20 
>[оверквотинг удален]
>5
>    oob-resync timeout 40
>    Hello due in 00:00:02
>  Index 1/1, flood queue length 0
>  Next 0x0(0)/0x0(0)
>  Last flood scan length is 0, maximum is 0
>  Last flood scan time is 0 msec, maximum is 0
>msec
>  Neighbor Count is 0, Adjacent neighbor count is 0
>  Suppress hello for 0 neighbor(s)

Судя по
m17#sh ip ospf nei

m17

у вас нет ни одного активного соединения OSPF.
Сделайте, что sh_  попросил. Дебаг скорее всего откроет глаза на проблему... .

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 22-Сен-10 13:44 
m17_ps69# debug ip ospf hell
OSPF hello events debugging is on

Это все.


"Не работает динамическая маршрутизация на 1700"
Отправлено lumenous , 22-Сен-10 13:59 
>m17_ps69# debug ip ospf hell
>OSPF hello events debugging is on
>
>Это все.

term mon наберите =)

"Не работает динамическая маршрутизация на 1700"
Отправлено Ivan Pomidorov , 22-Сен-10 14:03 
*Mar  8 21:25:25.313: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:25:25.317: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:25:25.317: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
*Mar  8 21:25:35.337: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:25:35.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:25:35.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
*Mar  8 21:25:45.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:25:45.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:25:45.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
*Mar  8 21:25:55.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:25:55.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:25:55.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
*Mar  8 21:26:05.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:26:05.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:26:05.341: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
*Mar  8 21:26:15.340: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:26:15.340: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:26:15.340: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
*Mar  8 21:26:25.340: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:26:25.340: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:26:25.340: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
*Mar  8 21:26:35.360: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.2 from 172.30.252.193
*Mar  8 21:26:35.360: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.3 from 172.30.252.227
*Mar  8 21:26:35.364: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0.4 from 172.30.252.236
"Не работает динамическая маршрутизация на 1700"
Отправлено lumenous , 22-Сен-10 14:09 
>[оверквотинг удален]
>*Mar  8 21:26:25.340: OSPF: Send hello to 224.0.0.5 area 0 on
>FastEthernet0.3 from 172.30.252.227
>*Mar  8 21:26:25.340: OSPF: Send hello to 224.0.0.5 area 0 on
>FastEthernet0.4 from 172.30.252.236
>*Mar  8 21:26:35.360: OSPF: Send hello to 224.0.0.5 area 0 on
>FastEthernet0.2 from 172.30.252.193
>*Mar  8 21:26:35.360: OSPF: Send hello to 224.0.0.5 area 0 on
>FastEthernet0.3 from 172.30.252.227
>*Mar  8 21:26:35.364: OSPF: Send hello to 224.0.0.5 area 0 on
>FastEthernet0.4 from 172.30.252.236

А конфиги другого роутера, откуда приходят маршруты по ospf можно как то посмотреть? И дебаг тоже.
А еще попробуйте  deb ip ospf events и error

"Не работает динамическая маршрутизация на 1700"
Отправлено sh_ , 22-Сен-10 14:33 
К вам не приходит ни одного hello от других маршрутизаторов. Вы вообще уверены, что на них поднят ospf?
"Не работает динамическая маршрутизация на 1700"
Отправлено fantom , 23-Сен-10 10:05 
>К вам не приходит ни одного hello от других маршрутизаторов. Вы вообще
>уверены, что на них поднят ospf?

Коммутатор рубит мультикаст с вероятностью 0.9 :)

"Не работает динамическая маршрутизация на 1700"
Отправлено sh_ , 23-Сен-10 11:50 

>Коммутатор рубит мультикаст с вероятностью 0.9 :)

Издеваетесь? :) Мне кажется, что провайдер и не собирался OSPF поднимать...

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 04-Окт-10 10:22 
Извините, за долгое молчание.

Вот конфиги основного и резервного ответных маршрутизеров подключеных к Moxe:

Это первый (основной):

m8#sh ip proto
Routing Protocol is "ospf 1"
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Router ID 192.169.140.9
  It is an autonomous system boundary router
  Redistributing External Routes from,
    static, includes subnets in redistribution
  Number of areas in this router is 1. 1 normal 0 stub 0 nssa
  Maximum path: 4
  Routing for Networks:
    172.30.64.32 0.0.0.15 area 0
    172.30.192.48 0.0.0.15 area 0
    172.30.252.0 0.0.0.3 area 0
    172.30.252.144 0.0.0.15 area 0
    172.30.252.160 0.0.0.31 area 0
    172.30.252.192 0.0.0.31 area 0
    172.30.252.224 0.0.0.7 area 0
    172.30.252.232 0.0.0.7 area 0
    192.169.3.20 0.0.0.3 area 0
    192.169.140.0 0.0.0.255 area 0
Reference bandwidth unit is 100 mbps
  Passive Interface(s):
    VoIP-Null0
...

m8#sh ip ospf int
FastEthernet0/0.5 is up, line protocol is up
  Internet Address 172.30.252.152/28, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.154
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.152
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:05
  Supports Link-local Signaling (LLS)
  Index 4/4, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.4 is up, line protocol is up
  Internet Address 172.30.252.233/29, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.234
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.233
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:02
  Supports Link-local Signaling (LLS)
  Index 6/6, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 12
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/1 is up, line protocol is up
  Internet Address 172.30.252.161/29, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.252.161
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.252.162
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:06
  Supports Link-local Signaling (LLS)
  Index 5/5, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
Serial0/1/0 is up, line protocol is up
  Internet Address 172.30.252.2/30, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type POINT_TO_POINT, Cost: 64
  Transmit Delay is 1 sec, State POINT_TO_POINT,
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:04
  Supports Link-local Signaling (LLS)
  Index 3/3, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 9, maximum is 12
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.168.4.1
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.1 is up, line protocol is up
  Internet Address 172.30.192.49/28, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.192.49
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.192.50
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:07
  Supports Link-local Signaling (LLS)
  Index 2/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.2 is up, line protocol is up
  Internet Address 172.30.64.33/28, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.64.33
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.64.34
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:08
  Supports Link-local Signaling (LLS)
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)


m8#debug ip ospf hell

Oct  4 06:08:21.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.49
Oct  4 06:08:21.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.33
Oct  4 06:08:22.182: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.152
Oct  4 06:08:22.830: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.5 172.30.252.154
Oct  4 06:08:22.830: OSPF: End of hello processing
Oct  4 06:08:24.094: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.4 172.30.252.234
Oct  4 06:08:24.094: OSPF: End of hello processing
Oct  4 06:08:25.242: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.161
Oct  4 06:08:25.558: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/1/0 from 172.30.252.2
Oct  4 06:08:27.126: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.1 172.30.192.50
Oct  4 06:08:27.126: OSPF: End of hello processing
Oct  4 06:08:27.126: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.2 172.30.64.34
Oct  4 06:08:27.126: OSPF: End of hello processing
Oct  4 06:08:28.574: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.233
Oct  4 06:08:28.662: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/1 172.30.252.162
Oct  4 06:08:28.662: OSPF: End of hello processing
Oct  4 06:08:30.786: OSPF: Rcv hello from 192.168.4.1 area 0 from Serial0/1/0 172.30.252.1
Oct  4 06:08:30.786: OSPF: End of hello processing
Oct  4 06:08:31.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.49
Oct  4 06:08:31.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.33
Oct  4 06:08:32.182: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.152
Oct  4 06:08:32.830: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.5 172.30.252.154
Oct  4 06:08:32.830: OSPF: End of hello processing
Oct  4 06:08:34.090: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.4 172.30.252.234
Oct  4 06:08:34.094: OSPF: End of hello processing
Oct  4 06:08:35.242: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.161
Oct  4 06:08:35.558: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/1/0 from 172.30.252.2
Oct  4 06:08:37.123: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.1 172.30.192.50
Oct  4 06:08:37.127: OSPF: End of hello processing
Oct  4 06:08:37.127: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.2 172.30.64.34
Oct  4 06:08:37.127: OSPF: End of hello processing
Oct  4 06:08:38.575: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.233
Oct  4 06:08:38.659: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/1 172.30.252.162
Oct  4 06:08:38.659: OSPF: End of hello processing
Oct  4 06:08:40.787: OSPF: Rcv hello from 192.168.4.1 area 0 from Serial0/1/0 172.30.252.1
Oct  4 06:08:40.787: OSPF: End of hello processing
Oct  4 06:08:41.603: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.49
Oct  4 06:08:41.603: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.33
Oct  4 06:08:42.183: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.152
Oct  4 06:08:42.827: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.5 172.30.252.154
Oct  4 06:08:42.827: OSPF: End of hello processing


Вот второй (резервный):

m9#sh ip proto
Routing Protocol is "ospf 1"
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Router ID 192.169.140.8
  Number of areas in this router is 1. 1 normal 0 stub 0 nssa
  Maximum path: 4
  Routing for Networks:
    172.30.64.32 0.0.0.15 area 0
    172.30.192.48 0.0.0.15 area 0
    172.30.252.0 0.0.0.3 area 0
    172.30.252.144 0.0.0.15 area 0
    172.30.252.160 0.0.0.31 area 0
    172.30.252.192 0.0.0.31 area 0
    172.30.252.224 0.0.0.7 area 0
    172.30.252.232 0.0.0.7 area 0
    192.169.3.20 0.0.0.3 area 0
    192.169.140.0 0.0.0.15 area 0
Reference bandwidth unit is 100 mbps
  Routing Information Sources:
    Gateway         Distance      Last Update
    172.24.86.253        110      1w3d
    172.18.242.8         110      6d20h
    172.30.196.34        110      00:00:05
    172.18.232.8         110      1w5d
    192.169.3.10         110      4d23h
    192.168.4.5          110      00:00:06
    192.168.4.1          110      00:00:06
    192.168.4.2          110      00:00:06
    192.169.21.1         110      00:00:06
    192.169.23.1         110      00:00:06
    172.30.66.17         110      00:00:06
    192.169.140.9        110      00:00:06
    192.169.140.8        110      4w2d
    192.169.140.10       110      00:00:06
    172.30.66.1          110      4d14h
    172.30.66.9          110      7w5d
  Distance: (default is 110)

m9#sh ip ospf int
FastEthernet0/0.4 is up, line protocol is up
  Internet Address 172.30.252.234/29, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.234
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.233
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:05
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 3/4, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/1 is up, line protocol is up
  Internet Address 172.30.252.162/29, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.252.161
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.252.162
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:08
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 4/5, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Designated Router)
  Suppress hello for 0 neighbor(s)
Serial0/0/0:0 is up, line protocol is up
  Internet Address 192.169.3.21/30, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type POINT_TO_POINT, Cost: 48
  Transmit Delay is 1 sec, State POINT_TO_POINT
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:06
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 6/6, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 172.30.66.1
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.5 is up, line protocol is up
  Internet Address 172.30.252.154/28, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.154
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.152
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:01
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 5/3, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.1 is up, line protocol is up
  Internet Address 172.30.192.50/28, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.192.49
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.192.50
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:04
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 2/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.2 is up, line protocol is up
  Internet Address 172.30.64.34/28, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.64.33
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.64.34
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:04
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Designated Router)
  Suppress hello for 0 neighbor(s)


m9#deb ip ospf hell

Oct  4 06:17:08.186: OSPF: Rcv hello from 172.30.66.1 area 0 from Serial0/0/0:0 192.169.3.22
Oct  4 06:17:08.186: OSPF: End of hello processing
Oct  4 06:17:08.594: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.4 172.30.252.233
Oct  4 06:17:08.594: OSPF: End of hello processing
Oct  4 06:17:08.622: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.162
Oct  4 06:17:11.622: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.1 172.30.192.49
Oct  4 06:17:11.622: OSPF: End of hello processing
Oct  4 06:17:11.622: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.2 172.30.64.33
Oct  4 06:17:11.622: OSPF: End of hello processing
Oct  4 06:17:12.202: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.5 172.30.252.152
Oct  4 06:17:12.202: OSPF: End of hello processing
Oct  4 06:17:12.790: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.154
Oct  4 06:17:14.054: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.234
Oct  4 06:17:15.262: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/1 172.30.252.161
Oct  4 06:17:15.262: OSPF: End of hello processing
Oct  4 06:17:17.086: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/0/0:0 from 192.169.3.21
Oct  4 06:17:17.086: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.50
Oct  4 06:17:17.086: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.34
Oct  4 06:17:18.002: OSPF: Rcv hello from 172.30.66.1 area 0 from Serial0/0/0:0 192.169.3.22
Oct  4 06:17:18.002: OSPF: End of hello processing
Oct  4 06:17:18.593: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.4 172.30.252.233
Oct  4 06:17:18.593: OSPF: End of hello processing
Oct  4 06:17:18.621: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.162
Oct  4 06:17:21.621: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.1 172.30.192.49
Oct  4 06:17:21.621: OSPF: End of hello processing
Oct  4 06:17:21.621: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.2 172.30.64.33
Oct  4 06:17:21.621: OSPF: End of hello processing
Oct  4 06:17:22.201: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.5 172.30.252.152
Oct  4 06:17:22.201: OSPF: End of hello processing
Oct  4 06:17:22.789: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.154
Oct  4 06:17:24.053: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.234
Oct  4 06:17:25.261: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/1 172.30.252.161
Oct  4 06:17:25.261: OSPF: End of hello processing
Oct  4 06:17:27.085: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/0/0:0 from 192.169.3.21
Oct  4 06:17:27.085: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.50
Oct  4 06:17:27.085: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.34
Oct  4 06:17:27.241: OSPF: Rcv hello from 172.30.66.1 area 0 from Serial0/0/0:0 192.169.3.22
Oct  4 06:17:27.241: OSPF: End of hello processing
Oct  4 06:17:28.593: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.4 172.30.252.233
Oct  4 06:17:28.597: OSPF: End of hello processing
Oct  4 06:17:28.621: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.162
Oct  4 06:17:31.624: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.1 172.30.192.49
Oct  4 06:17:31.624: OSPF: End of hello processing
Oct  4 06:17:31.624: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.2 172.30.64.33
Oct  4 06:17:31.624: OSPF: End of hello processing
Oct  4 06:17:32.204: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.5 172.30.252.152
Oct  4 06:17:32.204: OSPF: End of hello processing
Oct  4 06:17:32.788: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.154

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 04-Окт-10 10:25 
Извините, за долгое молчание.

Вот конфиги основного и резервного ответных маршрутизеров подключеных к Moxe:

Это первый (основной):

m8#sh ip proto
Routing Protocol is "ospf 1"
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Router ID 192.169.140.9
  It is an autonomous system boundary router
  Redistributing External Routes from,
    static, includes subnets in redistribution
  Number of areas in this router is 1. 1 normal 0 stub 0 nssa
  Maximum path: 4
  Routing for Networks:
    172.30.64.32 0.0.0.15 area 0
    172.30.192.48 0.0.0.15 area 0
    172.30.252.0 0.0.0.3 area 0
    172.30.252.144 0.0.0.15 area 0
    172.30.252.160 0.0.0.31 area 0
    172.30.252.192 0.0.0.31 area 0
    172.30.252.224 0.0.0.7 area 0
    172.30.252.232 0.0.0.7 area 0
    192.169.3.20 0.0.0.3 area 0
    192.169.140.0 0.0.0.255 area 0
Reference bandwidth unit is 100 mbps
  Passive Interface(s):
    VoIP-Null0
...

m8#sh ip ospf int
FastEthernet0/0.5 is up, line protocol is up
  Internet Address 172.30.252.152/28, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.154
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.152
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:05
  Supports Link-local Signaling (LLS)
  Index 4/4, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.4 is up, line protocol is up
  Internet Address 172.30.252.233/29, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.234
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.233
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:02
  Supports Link-local Signaling (LLS)
  Index 6/6, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 12
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/1 is up, line protocol is up
  Internet Address 172.30.252.161/29, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.252.161
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.252.162
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:06
  Supports Link-local Signaling (LLS)
  Index 5/5, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
Serial0/1/0 is up, line protocol is up
  Internet Address 172.30.252.2/30, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type POINT_TO_POINT, Cost: 64
  Transmit Delay is 1 sec, State POINT_TO_POINT,
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:04
  Supports Link-local Signaling (LLS)
  Index 3/3, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 9, maximum is 12
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.168.4.1
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.1 is up, line protocol is up
  Internet Address 172.30.192.49/28, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.192.49
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.192.50
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:07
  Supports Link-local Signaling (LLS)
  Index 2/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.2 is up, line protocol is up
  Internet Address 172.30.64.33/28, Area 0
  Process ID 1, Router ID 192.169.140.9, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.64.33
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.64.34
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:08
  Supports Link-local Signaling (LLS)
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 13
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.8  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)


m8#debug ip ospf hell

Oct  4 06:08:21.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.49
Oct  4 06:08:21.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.33
Oct  4 06:08:22.182: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.152
Oct  4 06:08:22.830: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.5 172.30.252.154
Oct  4 06:08:22.830: OSPF: End of hello processing
Oct  4 06:08:24.094: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.4 172.30.252.234
Oct  4 06:08:24.094: OSPF: End of hello processing
Oct  4 06:08:25.242: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.161
Oct  4 06:08:25.558: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/1/0 from 172.30.252.2
Oct  4 06:08:27.126: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.1 172.30.192.50
Oct  4 06:08:27.126: OSPF: End of hello processing
Oct  4 06:08:27.126: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.2 172.30.64.34
Oct  4 06:08:27.126: OSPF: End of hello processing
Oct  4 06:08:28.574: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.233
Oct  4 06:08:28.662: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/1 172.30.252.162
Oct  4 06:08:28.662: OSPF: End of hello processing
Oct  4 06:08:30.786: OSPF: Rcv hello from 192.168.4.1 area 0 from Serial0/1/0 172.30.252.1
Oct  4 06:08:30.786: OSPF: End of hello processing
Oct  4 06:08:31.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.49
Oct  4 06:08:31.602: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.33
Oct  4 06:08:32.182: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.152
Oct  4 06:08:32.830: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.5 172.30.252.154
Oct  4 06:08:32.830: OSPF: End of hello processing
Oct  4 06:08:34.090: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.4 172.30.252.234
Oct  4 06:08:34.094: OSPF: End of hello processing
Oct  4 06:08:35.242: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.161
Oct  4 06:08:35.558: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/1/0 from 172.30.252.2
Oct  4 06:08:37.123: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.1 172.30.192.50
Oct  4 06:08:37.127: OSPF: End of hello processing
Oct  4 06:08:37.127: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.2 172.30.64.34
Oct  4 06:08:37.127: OSPF: End of hello processing
Oct  4 06:08:38.575: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.233
Oct  4 06:08:38.659: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/1 172.30.252.162
Oct  4 06:08:38.659: OSPF: End of hello processing
Oct  4 06:08:40.787: OSPF: Rcv hello from 192.168.4.1 area 0 from Serial0/1/0 172.30.252.1
Oct  4 06:08:40.787: OSPF: End of hello processing
Oct  4 06:08:41.603: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.49
Oct  4 06:08:41.603: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.33
Oct  4 06:08:42.183: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.152
Oct  4 06:08:42.827: OSPF: Rcv hello from 192.169.140.8 area 0 from FastEthernet0/0.5 172.30.252.154
Oct  4 06:08:42.827: OSPF: End of hello processing


Вот второй (резервный):

m9#sh ip proto
Routing Protocol is "ospf 1"
  Outgoing update filter list for all interfaces is not set
  Incoming update filter list for all interfaces is not set
  Router ID 192.169.140.8
  Number of areas in this router is 1. 1 normal 0 stub 0 nssa
  Maximum path: 4
  Routing for Networks:
    172.30.64.32 0.0.0.15 area 0
    172.30.192.48 0.0.0.15 area 0
    172.30.252.0 0.0.0.3 area 0
    172.30.252.144 0.0.0.15 area 0
    172.30.252.160 0.0.0.31 area 0
    172.30.252.192 0.0.0.31 area 0
    172.30.252.224 0.0.0.7 area 0
    172.30.252.232 0.0.0.7 area 0
    192.169.3.20 0.0.0.3 area 0
    192.169.140.0 0.0.0.15 area 0
Reference bandwidth unit is 100 mbps
  Routing Information Sources:
    Gateway         Distance      Last Update
    172.24.86.253        110      1w3d
    172.18.242.8         110      6d20h
    172.30.196.34        110      00:00:05
    172.18.232.8         110      1w5d
    192.169.3.10         110      4d23h
    192.168.4.5          110      00:00:06
    192.168.4.1          110      00:00:06
    192.168.4.2          110      00:00:06
    192.169.21.1         110      00:00:06
    192.169.23.1         110      00:00:06
    172.30.66.17         110      00:00:06
    192.169.140.9        110      00:00:06
    192.169.140.8        110      4w2d
    192.169.140.10       110      00:00:06
    172.30.66.1          110      4d14h
    172.30.66.9          110      7w5d
  Distance: (default is 110)

m9#sh ip ospf int
FastEthernet0/0.4 is up, line protocol is up
  Internet Address 172.30.252.234/29, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.234
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.233
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:05
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 3/4, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/1 is up, line protocol is up
  Internet Address 172.30.252.162/29, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.252.161
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.252.162
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:08
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 4/5, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Designated Router)
  Suppress hello for 0 neighbor(s)
Serial0/0/0:0 is up, line protocol is up
  Internet Address 192.169.3.21/30, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type POINT_TO_POINT, Cost: 48
  Transmit Delay is 1 sec, State POINT_TO_POINT
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:06
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 6/6, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 172.30.66.1
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.5 is up, line protocol is up
  Internet Address 172.30.252.154/28, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State DR, Priority 1
  Designated Router (ID) 192.169.140.8, Interface address 172.30.252.154
  Backup Designated router (ID) 192.169.140.9, Interface address 172.30.252.152
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:01
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 5/3, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Backup Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.1 is up, line protocol is up
  Internet Address 172.30.192.50/28, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.192.49
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.192.50
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:04
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 2/2, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Designated Router)
  Suppress hello for 0 neighbor(s)
FastEthernet0/0.2 is up, line protocol is up
  Internet Address 172.30.64.34/28, Area 0
  Process ID 1, Router ID 192.169.140.8, Network Type BROADCAST, Cost: 1
  Transmit Delay is 1 sec, State BDR, Priority 1
  Designated Router (ID) 192.169.140.9, Interface address 172.30.64.33
  Backup Designated router (ID) 192.169.140.8, Interface address 172.30.64.34
  Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
    oob-resync timeout 40
    Hello due in 00:00:04
  Supports Link-local Signaling (LLS)
  Cisco NSF helper support enabled
  IETF NSF helper support enabled
  Index 1/1, flood queue length 0
  Next 0x0(0)/0x0(0)
  Last flood scan length is 1, maximum is 14
  Last flood scan time is 0 msec, maximum is 4 msec
  Neighbor Count is 1, Adjacent neighbor count is 1
    Adjacent with neighbor 192.169.140.9  (Designated Router)
  Suppress hello for 0 neighbor(s)


m9#deb ip ospf hell

Oct  4 06:17:08.186: OSPF: Rcv hello from 172.30.66.1 area 0 from Serial0/0/0:0 192.169.3.22
Oct  4 06:17:08.186: OSPF: End of hello processing
Oct  4 06:17:08.594: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.4 172.30.252.233
Oct  4 06:17:08.594: OSPF: End of hello processing
Oct  4 06:17:08.622: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.162
Oct  4 06:17:11.622: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.1 172.30.192.49
Oct  4 06:17:11.622: OSPF: End of hello processing
Oct  4 06:17:11.622: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.2 172.30.64.33
Oct  4 06:17:11.622: OSPF: End of hello processing
Oct  4 06:17:12.202: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.5 172.30.252.152
Oct  4 06:17:12.202: OSPF: End of hello processing
Oct  4 06:17:12.790: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.154
Oct  4 06:17:14.054: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.234
Oct  4 06:17:15.262: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/1 172.30.252.161
Oct  4 06:17:15.262: OSPF: End of hello processing
Oct  4 06:17:17.086: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/0/0:0 from 192.169.3.21
Oct  4 06:17:17.086: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.50
Oct  4 06:17:17.086: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.34
Oct  4 06:17:18.002: OSPF: Rcv hello from 172.30.66.1 area 0 from Serial0/0/0:0 192.169.3.22
Oct  4 06:17:18.002: OSPF: End of hello processing
Oct  4 06:17:18.593: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.4 172.30.252.233
Oct  4 06:17:18.593: OSPF: End of hello processing
Oct  4 06:17:18.621: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.162
Oct  4 06:17:21.621: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.1 172.30.192.49
Oct  4 06:17:21.621: OSPF: End of hello processing
Oct  4 06:17:21.621: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.2 172.30.64.33
Oct  4 06:17:21.621: OSPF: End of hello processing
Oct  4 06:17:22.201: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.5 172.30.252.152
Oct  4 06:17:22.201: OSPF: End of hello processing
Oct  4 06:17:22.789: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.154
Oct  4 06:17:24.053: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.4 from 172.30.252.234
Oct  4 06:17:25.261: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/1 172.30.252.161
Oct  4 06:17:25.261: OSPF: End of hello processing
Oct  4 06:17:27.085: OSPF: Send hello to 224.0.0.5 area 0 on Serial0/0/0:0 from 192.169.3.21
Oct  4 06:17:27.085: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.1 from 172.30.192.50
Oct  4 06:17:27.085: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.2 from 172.30.64.34
Oct  4 06:17:27.241: OSPF: Rcv hello from 172.30.66.1 area 0 from Serial0/0/0:0 192.169.3.22
Oct  4 06:17:27.241: OSPF: End of hello processing
Oct  4 06:17:28.593: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.4 172.30.252.233
Oct  4 06:17:28.597: OSPF: End of hello processing
Oct  4 06:17:28.621: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/1 from 172.30.252.162
Oct  4 06:17:31.624: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.1 172.30.192.49
Oct  4 06:17:31.624: OSPF: End of hello processing
Oct  4 06:17:31.624: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.2 172.30.64.33
Oct  4 06:17:31.624: OSPF: End of hello processing
Oct  4 06:17:32.204: OSPF: Rcv hello from 192.169.140.9 area 0 from FastEthernet0/0.5 172.30.252.152
Oct  4 06:17:32.204: OSPF: End of hello processing
Oct  4 06:17:32.788: OSPF: Send hello to 224.0.0.5 area 0 on FastEthernet0/0.5 from 172.30.252.154

"Не работает динамическая маршрутизация на 1700"
Отправлено lumenous , 04-Окт-10 11:45 
>[оверквотинг удален]
> FastEthernet0/0.1 172.30.192.49
> Oct  4 06:17:31.624: OSPF: End of hello processing
> Oct  4 06:17:31.624: OSPF: Rcv hello from 192.169.140.9 area 0 from
> FastEthernet0/0.2 172.30.64.33
> Oct  4 06:17:31.624: OSPF: End of hello processing
> Oct  4 06:17:32.204: OSPF: Rcv hello from 192.169.140.9 area 0 from
> FastEthernet0/0.5 172.30.252.152
> Oct  4 06:17:32.204: OSPF: End of hello processing
> Oct  4 06:17:32.788: OSPF: Send hello to 224.0.0.5 area 0 on
> FastEthernet0/0.5 from 172.30.252.154

Ну судя по тому, что Вы выложили, все у Вас работает.
Или какие-то проблемы еще есть?

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 04-Окт-10 16:23 
К сожалению, нет, ничего не работает.
Эти ospf hello приходят от ругих маршрутиазторов, с другими маршрутами. А нужные должны приходить от 172.30.252.193.
Да и на самом маршрутизаторе 1721 ответов то собственно и нет.
"Не работает динамическая маршрутизация на 1700"
Отправлено lumenous , 04-Окт-10 17:11 
> К сожалению, нет, ничего не работает.
> Эти ospf hello приходят от ругих маршрутиазторов, с другими маршрутами. А нужные
> должны приходить от 172.30.252.193.
> Да и на самом маршрутизаторе 1721 ответов то собственно и нет.

Ну тогда как и говорили - надо смотреть что на той стороне происходит... .

"Не работает динамическая маршрутизация на 1700"
Отправлено lumenous , 04-Окт-10 17:19 
>> К сожалению, нет, ничего не работает.
>> Эти ospf hello приходят от ругих маршрутиазторов, с другими маршрутами. А нужные
>> должны приходить от 172.30.252.193.
>> Да и на самом маршрутизаторе 1721 ответов то собственно и нет.
> Ну тогда как и говорили - надо смотреть что на той стороне
> происходит... .

А, понял вы уже показали с обоих конфиги.
Тогда скажите какими интерфейсами они между собой соединяются? Не увидел нигде интерфейса, куда входил бы 172.30.252.193.

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 05-Окт-10 08:44 
> А, понял вы уже показали с обоих конфиги.
> Тогда скажите какими интерфейсами они между собой соединяются? Не увидел нигде интерфейса,
> куда входил бы 172.30.252.193.

Выкладываю схемку сети
<a href='http://webfile.ru/4788544'>Скачать Рисунок2.png с WebFile.RU</a>

Конфиги со всех трех маршрутизаторов я выкладывал.

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 05-Окт-10 09:49 
> А, понял вы уже показали с обоих конфиги.
> Тогда скажите какими интерфейсами они между собой соединяются? Не увидел нигде интерфейса,
> куда входил бы 172.30.252.193.

Выкладываю схемку сети
<a href='http://webfile.ru/4788626'>Скачать Рисунок2.png с WebFile.RU</a>

Конфиги всех маршрутизаторов выкладывал выше

"Не работает динамическая маршрутизация на 1700"
Отправлено lumenous , 05-Окт-10 10:42 
>> А, понял вы уже показали с обоих конфиги.
>> Тогда скажите какими интерфейсами они между собой соединяются? Не увидел нигде интерфейса,
>> куда входил бы 172.30.252.193.
> Выкладываю схемку сети
> <a href='http://webfile.ru/4788626'>Скачать Рисунок2.png с WebFile.RU</a>
> Конфиги всех маршрутизаторов выкладывал выше

Понятно.
Тут возникало предположение, что коммутатор не пропускает мультикаст.
Как вариант - можно попробовать снифером посмотреть что приходит и уходит с коммутатора.
Учитывая что у вас даже Hello пакеты не долетают до роутеров, такая ситуация имеет право на существование =)

"Не работает динамическая маршрутизация на 1700"
Отправлено rapport_mur , 04-Окт-10 16:27 
> А конфиги другого роутера, откуда приходят маршруты по ospf можно как то
> посмотреть? И дебаг тоже.
> А еще попробуйте  deb ip ospf events и error

deb ip ospf events ничего не показывает
deb ip ospf error воопще отсутсвует