Всем привет.
понадобилось вот соединить 2 циски через серийные порты. С одной стороны 3640 с модулем NM-4a/s, с другой 1721 с модулем wic 2 a/s.
В 3640 воткнул V.35 DCE в 1721 V.35 DTE кабели, соединил их, циски настроил как написано здесь: http://cisco.com/en/US/tech/tk713/tk317/technologies_configu...
и что имеем. С обоих сторон Serial is up, line protocol is down3640#sh controllers s0/0
CD2430 Slot 0, Port 0, Controller 0, Channel 0, Revision 18
Channel mode is synchronous serial
idb 0x6212E60C, buffer size 1524, V.35 DCE cable, clockrate 640001721#sh controllers s0
Interface Serial0
Hardware is PowerQUICC MPC860
DTE V.35 clocks stopped.я так понимаю что проблема как раз с клоками на 1721, в чем может быть причина, не подскажите ? Спасибо заранее.
s run int serX/Y с обоих сторон!
>s run int serX/Y с обоих сторон!1721#sh int s0
Serial0 is up, line protocol is down
Hardware is PowerQUICC Serial
Internet address is 192.168.0.2/30
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
208 packets output, 5349 bytes, 0 underruns
0 output errors, 0 collisions, 71 interface resets
0 output buffer failures, 0 output buffers swapped out
140 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
3640#sh int s0/0
Serial0/0 is up, line protocol is down
Hardware is CD2430 in sync mode
Internet address is 192.168.0.1/30
MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output 00:00:09, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/32 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
216 packets output, 5958 bytes, 0 underruns
0 output errors, 0 collisions, 72 interface resets
0 output buffer failures, 0 output buffers swapped out
143 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
А может всетаки покажете s RUN int serX/Y с обоих сторон!
P.S.
Попробуйте поиграцца:
Router(config-if)# physical-layer {sync | async}И, я надеюсь, Вы понимаете что в синхронном режиме такие модули больше 128K не дадут!
>P.S.
>Попробуйте поиграцца:
>Router(config-if)# physical-layer {sync | async}
>
>И, я надеюсь, Вы понимаете что в синхронном режиме такие модули больше
>128K не дадут!мне скорость не важна, главное чтоб зацепились.
показать sh run обеих цисок ?
>мне скорость не важна, главное чтоб зацепились.
OK!
>показать sh run обеих цисок ?
ну не знаю... как вам будет угодноВы пытались поиграцца?
interface SerialX/Y
physical-layer sync
>>мне скорость не важна, главное чтоб зацепились.
>OK!
>>показать sh run обеих цисок ?
>ну не знаю... как вам будет угодно
>
>Вы пытались поиграцца?
>interface SerialX/Y
>physical-layer syncда пытался, результат тотже
вот конфиги:3640
interface Serial0/0
ip address 192.168.0.1 255.255.255.252
clockrate 640001721
interface Serial0
ip address 192.168.0.2 255.255.255.252
Все это очень странно, т.к. как вы говорите что физика у вас в up'е на обеих сторонах, а лайн протокол в дауне - так ли это?Как вариант попробуйте изменить энкапсуляцию с hdlc на PPP например.
>Все это очень странно, т.к. как вы говорите что физика у вас
>в up'е на обеих сторонах, а лайн протокол в дауне -
>так ли это?да, именно так
>
>Как вариант попробуйте изменить энкапсуляцию с hdlc на PPP например.ok попробую. спасибо.