Есть тестовый стенд Cisco 805 --> COMTREND SHDSL NTU CT-212 (в режиме LT)======COMTREND SHDSL NTU CT-212 (в режиме NT)--> Cisco 805.
Модемы находятся в конекте (соеденены через Line пачкордом). Cisco соеденены с ними через Serial (на модеме V.35). На обоих Cisco Ethernet0 настроен на разные подсети, но они друг друга не видят(пробовал cisco ping). Как настроить соединение Cisco 805 --> COMTREND SHDSL NTU CT-212, как рассказать Cisco о shdsl modeme?
sh run
Покажите.
>sh run
>Покажите.Current configuration : 618 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname router
!
logging queue-limit 100
enable secret 5 $1$k127$y2jVCOomEV5OoRf3S7HDp1
enable password bankbb
!
ip subnet-zero
no ip routing
!
!
!
!
!
interface Ethernet0
ip address 10.48.1.1 255.255.255.0
no ip route-cache
no cdp enable
!
interface Serial0
no ip address
no ip route-cache
!
ip classless
ip http server
!
!
snmp-server community router RO
snmp-server enable traps tty
!
line con 0
exec-timeout 0 0
stopbits 1
line vty 0 4
password dfbbb
login
!
endЯ пологаю необходимо задать Ip для serial0. Подскажите как?
Всё правильно вы предполагаете.
Задается все очень просто:
conf t
int s0
ip addr 10.10.10.1 255.255.255.252
endНа втором маршртизаторе то же самое, только адрес 10.10.10.2
Вот что у меня вышло но пинг и трасса не проходят дальше первой cisco.
Для первой cisco
Current configuration : 702 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname *****
!
logging queue-limit 100
enable secret 5 $1$SZO/$QAeBg.7ljSxIwSAAq0oWU.
enable password ****
!
ip subnet-zero
no ip routing
!
!
!
!
interface Ethernet0
ip address 192.168.48.10 255.255.255.0
no ip route-cache
no cdp enable
!
interface Serial0
ip address 10.48.2.2 255.255.255.252
no ip route-cache
!
ip classless
ip route profile
ip route 10.48.0.0 255.255.0.0 10.48.2.1
ip http server
!
!
snmp-server community ***** RO
snmp-server enable traps tty
!
line con 0
exec-timeout 0 0
stopbits 1
line vty 0 4
password *****
login
!
EndДля второй cisco
Current configuration : 641 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname *******
!
logging queue-limit 100
enable secret 5 $1$k127$y2jVCOomEV5OoRf3S7HDp1
enable password *****
!
ip subnet-zero
no ip routing
!
!
!
!
interface Ethernet0
ip address 10.48.1.1 255.255.255.0
no ip route-cache
no cdp enable
!
interface Serial0
ip address 10.48.2.1 255.255.255.252
no ip route-cache
!
ip classless
ip http server
!
!
snmp-server community ***** RO
snmp-server enable traps tty
!
line con 0
exec-timeout 0 0
stopbits 1
line vty 0 4
password *****
login
!
endМожет Cisco нада расказать о самом serial0, его параметры соединения и работы???
Почему Serial интерфейс Cisco1 не пингуется на ней самой, но вполне пингуется на Cisco2, находящейся с другой стороны модемной связки? Как это исправить?
>Почему Serial интерфейс Cisco1 не пингуется на ней самой, но вполне пингуется
>на Cisco2, находящейся с другой стороны модемной связки? Как это исправить?
>на второй циске тоже роутинг пропишите.
>>Почему Serial интерфейс Cisco1 не пингуется на ней самой, но вполне пингуется
>>на Cisco2, находящейся с другой стороны модемной связки? Как это исправить?
>>
>
>на второй циске тоже роутинг пропишите.Прописан, она сама себя не пингует, а удаленную вполне нормально.
sh ip int brie
sh int s0
Покажите вывод команд на обоих cisco!
>sh ip int brie
>sh int s0
>Покажите вывод команд на обоих cisco!первая
*****#sh ip int brie
Interface IP-Address OK? Method Status Prol
Serial0 10.48.2.1 YES manual up up
Ethernet0 192.168.48.10 YES NVRAM up up
******#sh int s0
Serial0 is up, line protocol is up
Hardware is PowerQUICC Serial
Internet address is 10.48.2.1/30
MTU 1500 bytes, BW 512 Kbit, DLY 20000 usec,
reliability 128/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:04, output 00:00:05, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/128 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 384 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
308 packets input, 21671 bytes, 0 no buffe
Received 286 broadcasts, 0 runts, 0 giants, 0 throttles
11627 input errors, 0 CRC, 11317 frame, 0 overrun, 7 ignored, 303 abort
335 packets output, 25624 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=upвторая
*****>sh ip int brie
Interface IP-Address OK? Method Status Prol
Serial0 10.48.2.2 YES manual up up
Ethernet0 10.48.1.1 YES NVRAM up dow
******>sh int s0
Serial0 is up, line protocol is up
Hardware is PowerQUICC Serial
Internet address is 10.48.2.2/30
MTU 1500 bytes, BW 512 Kbit, DLY 20000 usec,
reliability 132/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input 00:00:05, output 00:00:04, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/128 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 384 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
345 packets input, 26108 bytes, 0 no buffer
Received 308 broadcasts, 0 runts, 0 giants, 0 throttles
12076 input errors, 0 CRC, 11748 frame, 0 overrun, 3 ignored, 325 abort
337 packets output, 23787 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=down
А тебя не смущает?
11627 input errors, 0 CRC, 11317 frame, 0 overrun, 7 ignored, 303 abort
12076 input errors, 0 CRC, 11748 frame, 0 overrun, 3 ignored, 325 abortИ второе - какие клоки у тебя настроены на модемах?
>А тебя не смущает?
>11627 input errors, 0 CRC, 11317 frame, 0 overrun, 7 ignored, 303
>abort
>12076 input errors, 0 CRC, 11748 frame, 0 overrun, 3 ignored, 325
>abort
>
>И второе - какие клоки у тебя настроены на модемах?Возможно это из-за не подключенного Ethernet кабеля к цискам?
Клоки? Я не понимаю про что реч.
>Возможно это из-за не подключенного Ethernet кабеля к цискам?
Эзер тут не причем! CRC у тебя на Serial'е на входе!>Клоки? Я не понимаю про что реч.
Ну я так понимаю у тебя DTE - cisco, соответственно DCE должен быть модем, соответственно какие clock'и настроены на модемах? должно быть не более 512Kbit!
>>Возможно это из-за не подключенного Ethernet кабеля к цискам?
>Эзер тут не причем! CRC у тебя на Serial'е на входе!
>
>>Клоки? Я не понимаю про что реч.
>Ну я так понимаю у тебя DTE - cisco, соответственно DCE должен
>быть модем, соответственно какие clock'и настроены на модемах? должно быть не
>более 512Kbit!Не нашол в модеме намека на clock. В каком разделе он должен быть настройки v35 ?
У меня Cisco 805 + SHDSL modem
>Не нашол в модеме намека на clock. В каком разделе он должен
>быть настройки v35 ?
я не знаю какой у тебя модем - посмотри user guide чтоли по этому модему!
>У меня Cisco 805 + SHDSL modem
sh contr ser 0
>>Не нашол в модеме намека на clock. В каком разделе он должен
>>быть настройки v35 ?
>я не знаю какой у тебя модем - посмотри user guide чтоли
>по этому модему!
>>У меня Cisco 805 + SHDSL modem
>sh contr ser 0Interface Serial0
Hardware is PowerQUICC MPC850
DTE V.35 TX and RX clocks detected.
idb at 0x28CBAA4, driver data structure at 0x28D1CCC
SCC Registers:
General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x0
Events [SCCE]=0x0300, Mask [SCCM]=0x001F, Status [SCCS]=0x06
Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E
Interrupt Registers:
Config [CICR]=0x00368381, Pending [CIPR]=0x00000240
Mask [CIMR]=0x3024008A, In-srv [CISR]=0x00000000
Command register [CR]=0x280
Port A [PADIR]=0x0000, [PAPAR]=0x0FCC
[PAODR]=0x0000, [PADAT]=0x02CF
Port B [PBDIR]=0x0E1EE, [PBPAR]=0x020DE
[PBODR]=0x00000, [PBDAT]=0x0508F
Port C [PCDIR]=0x006, [PCPAR]=0x004
[PCSO]=0x8C0, [PCDAT]=0x438, [PCINT]=0x000
Receive Ring
rmd(2202B30): status 9000 length 1 address B7FC4
rmd(2202B38): status 9000 length 100 address B7A44
rmd(2202B40): status 9000 length 100 address B6C84
rmd(2202B48): status 9000 length 100 address B6DE4
rmd(2202B50): status 9000 length 100 address B74C4
rmd(2202B58): status 9000 length 100 address B6F44
rmd(2202B60): status 9000 length 100 address B7364
rmd(2202B68): status 9000 length 100 address B7BA4
rmd(2202B70): status 9000 length 100 address B6444
rmd(2202B78): status 9000 length 100 address B8124
rmd(2202B80): status 9000 length 100 address B7D04
rmd(2202B88): status 9000 length 100 address B65A4
rmd(2202B90): status 9000 length 100 address B62E4
rmd(2202B98): status 9000 length 100 address B7624
rmd(2202BA0): status 9000 length 100 address B7204
rmd(2202BA8): status B000 length 100 address B70A4
Transmit Ring
tmd(2202BB0): status 0 length 18 address 0
tmd(2202BB8): status 0 length 18 address 0
tmd(2202BC0): status 0 length 68 address 0
tmd(2202BC8): status 0 length 68 address 0
tmd(2202BD0): status 0 length 68 address 0
tmd(2202BD8): status 0 length 0 address 0
tmd(2202BE0): status 0 length 0 address 0
tmd(2202BE8): status 0 length 0 address 0
tmd(2202BF0): status 0 length 0 address 0
tmd(2202BF8): status 0 length 0 address 0
tmd(2202C00): status 0 length 0 address 0
tmd(2202C08): status 0 length 0 address 0
tmd(2202C10): status 0 length 0 address 0
tmd(2202C18): status 0 length 2058 address 0
tmd(2202C20): status 0 length 2 address 0
tmd(2202C28): status 2000 length 2780 address 0SCC GENERAL PARAMETER RAM (at 0x2203E00)
Rx BD Base [RBASE]=0xB30, Fn Code [RFCR]=0x18
Tx BD Base [TBASE]=0xBB0, Fn Code [TFCR]=0x18
Max Rx Buff Len [MRBLR]=256
Rx State [RSTATE]=0x0, BD Ptr [RBPTR]=0xB30
Tx State [TSTATE]=0x0, BD Ptr [TBPTR]=0xBB0SCC HDLC PARAMETER RAM (at 0x2203E38)
CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0
Nonmatch Addr Cntr [NMARC]=0
Retry Count [RETRC]=0
Max Frame Length [MFLR]=1608
Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=65535
User-defined Address 0000/0000/0000/0000
User-defined Address Mask 0x0000
buffer size 1524PowerQUICC SCC specific errors:
128334 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS lostsSCC HDLC PARAMETER RAM (at 0x2203E38)
CRC Preset [C_PRES]=0xFFFF, Mask [C_MASK]=0xF0B8
Errors: CRC [CRCEC]=0, Aborts [ABTSC]=0, Discards [DISFC]=0
Nonmatch Addr Cntr [NMARC]=0
Retry Count [RETRC]=0
Max Frame Length [MFLR]=1608
Rx Int Threshold [RFTHR]=0, Frame Cnt [RFCNT]=65535
User-defined Address 0000/0000/0000/0000
User-defined Address Mask 0x0000
buffer size 1524PowerQUICC SCC specific errors:
128334 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns
0 transmitter underruns
0 transmitter CTS losts
The V.35 Interface Configuration screen shown in Figure 4-9 allows the user to
set the signal RTS to Permanent On or From DTE and to enable the Tail
function to accept a clock from DTE V.35 interface.и параметры
RTS Permanent On: Permanent On From_DTE
Tail on/Off: Tail_on Tail_off
Data Invert: Normal Invert
Все верно - твоя cisco выступает DTE
DTE V.35 TX and RX clocks detected.Соответственно модем DCE - читай матчасть по модему!
>Все верно - твоя cisco выступает DTE
>DTE V.35 TX and RX clocks detected.
>
>Соответственно модем DCE - читай матчасть по модему!
Может что -то из этого?
Select Main Menu>Configuration>System Configuration to go to the System
Configuration screen shown in Figure 4-3. In the system configuration Menu
screen, two parameters are included: Device Name and Timing Source.
!" Device Name: Enter proper characters for system identification. The
maximum length for device name is eight characters. Only alphabetic and
numeric characters are valid.
!" Timing Source: Different NE modes provide different options of the timing
source. In LT Mode, the options are: Internal, SHDSL_LOOP, and DTE
LOOP. In NT Mode, the options are Internal, SHDSL_LOOP, DTE LOOP,
and Download Loop.
After making a selection, use the Up/Down arrow key to exit or confirm the
setting.