Это оригинальный конфиг, если кто юзает, поясните плиз!sniff 0 # 0 = not setting PROMISC mode
# 1 = put interface in PROMISC mode
database mysql # must be mysql for now
mysql_user acct # usually you don't need to change this
mysql_password acct_password # change this to your password
mysql_host localhost # sometimes you need to change this to
# 127.0.0.1 instead of localhost
mysql_port 0 # mysql port, 0 if you are using a socket
mysql_database netacct # usually you don't need to change this
pidfile /var/run/nacctd.pid # set pid file
# tis will help if you want to
# two (or more) nacctd on same machine
compactnet 62.73.77.0 255.255.255.0
compactnet 192.168.1.0 255.255.255.0
# log traffic only for these networks
# all other packets are NOT logged
ournet 62.73.77.0 255.255.255.0
# Ours IP nets for diferenciation of
# peering traffic types
direct_peer 217.75.132.0 255.255.255.0
direct_peer 62.176.90.0 255.255.255.0
direct_peer 62.73.86.0 255.255.255.0
direct_peer 62.73.87.0 255.255.255.0
direct_peer 194.12.226.80 255.255.255.240
direct_peer 194.12.233.96 255.255.255.224
direct_peer 194.12.233.160 255.255.255.224
# log traffic between 2 or more regional ISP-s
flush 300 # flush every 5 minutes
# this gives the interval in seconds
# when the accumulated data is flushed
# to the output file
fdelay 60 # this defines after how many seconds
# of inactivity a certain record of
# traffic information may be written out
# this helps making the logfiles smaller
# since only one output record will be
# generated for related traffic
notdev eth1 # Dont log entries for this device
# Use this on routers that you dont
# log forwarded packets twice.
device eth0 # device to put into promiscous mode
# you can specify as many as you want
# and you don't have to specify one
# (e.g. if this runs on your router)
#
# if you plan to use it on some *BSD
# system put here apropriate device
# i.e. - device ep0
# iflimit eth0 # on machines with multiple interfaces,
# log only packets on this interface
# mutually exclusive with hostlimit
# ignoremask 255.255.255.0 # Ignore traffic on same class C net
# This means traffic that is on
# your local LAN is not counted.
# This is useful for NFS etc.
# Not giving this option causes everything
# to be counted.
# This can degrade performance seriously!
ignorenet 127.0.0.0 255.0.0.0 # ignore loopback net
# You can define as many ignorenets as
# you want. Ignoring a net with
# ignorenet is not as efficient as
# ignoremask. Thus you should exclude
# your local network with ignoremask,
# not with ignorenet (although this is
# is possible).
debug 0 # set debugging level
debugfile /tmp/nacctd.debug # where to put debugging info
# Device configuration
# Defines where the real data starts for each type of interface
# First give the name prefix, then the offset in bytes to the start
# of the real data, then the offset of the type field in bytes. If
# there is no type field, just give a 0.
# Don't specify SLIP or PPP devices here, otherwise association of
# dynamic ip-addresses with usernames won't work
# Put device types with more traffic last.
headers tr 40 38
headers lo 14 12
headers isdn 4 0
# headers isdn 14 0 # for hdlc/trans/cisco and hdlc/trans/raw
headers eth 14 12
headers plip 14 12
# hostlimit 12.34.56.78 # log only packets to/from this host
# hostlimit 34.56.78.12 # and this one too
# this option is mutually exclusive with iflimit
Подскажите плиз у кого это работае правильно, помогите разобраться!
Имеется два канала к прову eth1 1.1.1.1, eth2 2.2.2.2
И один eth0 192.168.1.0 локалка. Все это дело с тоит на шлюзе с проксей. Надо считать трафик на два канала инета. Но еще есть один внешний адрес, который считать не надо!