Не ходят факсы по VoIP ч/з Cisco 3640, т.е. ходят, но ооооочень плохо и даже не ч/з раз, а ч/з 5 раз :(dial-peer voice 80 voip
preference 5
max-conn 3
destination-pattern 8T
session target ipv4:xxx.xxx.xxx.xxx
fax-relay ecm disable
fax rate 4800
fax protocol t38 ls-redundancy 5 hs-redundancy 2
пробовал менять fax rate, пробовал все что угодно. - результат либо вообще не идут, либо ч/з раз.Скажите, это общая проблема и с ней надо смериться, т.к. многие операторы впринципе не гарантируют передачу факсов ч/з VoIP или можно еще подергаться?
Каналы везде выделенные ч/з Equant
вот debug fax relay:Mar 5 08:26:39: 1/1/0:3543 256778447 fr-entered (10ms)
Mar 5 08:26:40: 1/1/0:3543 256780260 fr-msg-tx CSI
Mar 5 08:26:41: 1/1/0:3543 256781400 fr-msg-tx DIS
Mar 5 08:26:44: 1/1/0:3543 256783630 fr-msg-det DCS
Mar 5 08:26:46: 1/1/0:3543 256786010 fr-msg-tx NSF
Mar 5 08:26:47: 1/1/0:3543 256787220 fr-msg-tx CSI
Mar 5 08:26:48: 1/1/0:3543 256787960 fr-msg-tx DIS
Mar 5 08:26:51: 1/1/0:3543 256790770 fr-msg-det DCS
Mar 5 08:26:57: 1/1/0:3543 256796710 fr-msg-tx FTT
Mar 5 08:26:58: 1/1/0:3543 256797920 fr-msg-det DCS
Mar 5 08:27:04: 1/1/0:3543 256804140 fr-msg-tx FTT
Mar 5 08:27:06: 1/1/0:3543 256805870 fr-msg-det DCS
Mar 5 08:27:12: 1/1/0:3543 256811740 fr-msg-tx FTT
Mar 5 08:27:14: 1/1/0:3543 256813470 fr-msg-det DCS
Mar 5 08:27:20: 1/1/0:3543 256819650 fr-msg-tx FTT
Mar 5 08:27:21: 1/1/0:3543 256821380 fr-msg-det DCS
Mar 5 08:27:28: 1/1/0:3543 256827560 fr-msg-tx FTT
Mar 5 08:27:29: 1/1/0:3543 256829290 fr-msg-det DCN
Выбирайте сами, что для вас важнее, передача факсов или возможность выбора одного из нескольких голосовых кодеков.
Cross-Platform Release Notes for Cisco IOS Release 12.2 T, Part 7:
Caveats for 12.2(2)T through 12.2(11)T10
http://www.cisco.com/univercd/cc/td/doc/product/software/ios...* CSCeb01641
Symptoms: T.38 fax calls may fail if the terminating gateway sends fast start
elements in multiple H.225 messages (for example, call_proceeding, alert, connect).Conditions: This symptom is observed only with T.38 fax calls that go through an
IP in IP (IPIP) gateway and is specific to fast start calls when non-Cisco
gateways are used for the terminating gateway.
The symptom is not observed on a Cisco gateway.Workaround: Initiate the T.38 fax calls using H.323 slow start.
* CSCea20911
Symptoms: T.38 fax calls fail when FastStart is used with more than one codec proposed.
Conditions: This symptom is observed with IPIP gateways.
Workaround: Use SlowStart for any calls that require fax.
* CSCdz74292
Symptoms: T.38 fax calls from one gateway to another gateway may fail.
Conditions: This symptom is observed when you make a T.38 fax call from
an originating gateway (OGW) that is running Cisco IOS Release 12.2(13)T
and that is configured for H.323 fast start mode through a gatekeeper to
a gateway that is running Release 12.2(11)T2.Workaround: Configure the voice service voip global configuration command
followed by the h323 call start slow voice-service configuration command
on the OGW.* CSCin32436
Symptoms: T.38 fax relay calls cannot be made.
Conditions: This symptom is observed when a T.38 fax relay call is placed
between a Cisco 3640 and a Cisco Catalyst 4000.Workaround: Enable fallback to Cisco fax relay.
* CSCdu79392
Symptoms An H.245 connection may enter an indefinite loop because of
asymmetric codec negotiation failure with slow-start calls.Conditions This symptom is observed when slow-start calls are made
using a voice class codec configuration in a Voice over IP (VoIP) dial peer.Workaround Configure the codec directly on the VoIP dial peer with slow-start calls.
Спасибо за ответ.
А как сделать slow-start к факсам?
Это на факсах делается или на cisco?
кстати, версии на cisco
Version 12.2(11)T8
на другой
Version 12.2(8)T
>Спасибо за ответ.
>А как сделать slow-start к факсам?
>Это на факсах делается или на cisco?
попробуй сделать voice class h323 и в него вбей slow start
потом прицепи этот класс к диалпиру, по которым у тебя факсы ходят.
>>Спасибо за ответ.
>>А как сделать slow-start к факсам?
>>Это на факсах делается или на cisco?
>
>
>попробуй сделать voice class h323 и в него вбей slow start
>потом прицепи этот класс к диалпиру, по которым у тебя факсы ходят.
>да, я уже и сам нашел :)
еще можно в global parametersvoice service voip
h323
call start slowно все равно не ходят, чтоб они были здоровы...блин :)
я так понял надо IOS менять?
я согласен пока на все, кодек использую один - g729r8
еще что-нибудь посоветуете?