The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]



Вариант для распечатки  
Пред. тема | След. тема 
Форум Разговоры, обсуждение новостей
Режим отображения отдельной подветви беседы [ Отслеживать ]

Оглавление

Отчёт о развитии FreeBSD за четвёртый квартал 2015 года, opennews (??), 08-Фев-16, (0) [смотреть все] +1

Сообщения [Сортировка по времени | RSS]


131. "Отчёт о развитии FreeBSD за четвёртый квартал 2015 года"  –1 +/
Сообщение от uniman_ (?), 14-Фев-16, 11:30 
>Например, у Raspberry Pi загрузка возможна исключительно с SD-карточки.

http://blogs.wcode.org/2013/09/howto-netboot-a-raspberry-pi/

Update: if you want the kernel on a network too…

@barnoid writes to mention that U-Boot allows you to netboot the entire OS (although because of the Pi’s limitations, you still have to load the U-Boot code from an SD card). We haven’t played with this yet, though.

2013 год, Карл.

>Грузимся с карточки и переводим стрелки на USB-HDD

Че, бакланим по фене, чувак? =)

И стрелки ты переведешь до первого похода USB-HDD в несознанку.
Скинет этот фраер коннектор и ищи его.
Так что карточку не мохнать, она надежная.


Ответить | Правка | Наверх | Cообщить модератору

132. "Отчёт о развитии FreeBSD за четвёртый квартал 2015 года"  +1 +/
Сообщение от DeadLoco (ok), 14-Фев-16, 11:47 
> you still have to load the U-Boot code from an SD card

Какую букву вам перевести?

Ответить | Правка | Наверх | Cообщить модератору

135. "Отчёт о развитии FreeBSD за четвёртый квартал 2015 года"  –2 +/
Сообщение от _uniman (?), 15-Фев-16, 15:26 
>> you still have to load the U-Boot code from an SD card
>Какую букву вам перевести?

Внезапно:

https://github.com/raspberrypi/firmware

* ./boot: start*.elf, bootcode.bin are the GPU firmware and bootloaders.
  Their licence is described in 'LICENCE.broadcom'. The kernel*.img and *.dtb
  files are builds of the Linux kernel, released under the GPL (see COPYING.linux)

PHASE ONE: Initialize the hardware
==================================

This first boot phase is common to any use of RaspberryPi, whether
you're booting Linux, FreeBSD, or any other software.  It loads a
series of proprietary boot loader files that initialize the
hardware and ultimately load and run some executable.

https://github.com/freebsd/crochet/tree/master/board/Raspber...

These initial bits are loaded from the first partition on the SD card.
That partition must be formatted as FAT16 or FAT32.

* At power on, the ARM core is off and the GPU is on.  SDRAM is disabled.
* GPU ROM code reads bootcode.bin from SD card and executes it on the GPU.
* bootcode.bin enables SDRAM and loads start.elf

...

Далее u-boot, и загрузка ядра из сети.
В чем проблемы? Что первичный загрузчик (проприентарный) считываеться GPU from board SD card?

Ответить | Правка | Наверх | Cообщить модератору

Архив | Удалить

Рекомендовать для помещения в FAQ | Индекс форумов | Темы | Пред. тема | След. тема




Партнёры:
PostgresPro
Inferno Solutions
Hosting by Hoster.ru
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2024 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру