Ошибки lost carrier, и потери пакетов на интерфейсе., trial, 06-Апр-05, 10:43 [смотреть все]Добрый день! Уважаемые, может кто сталкивался, с чем связаны ошибки на интерфейсах lost carrier, и как можно избавится от этого.Схема сети следующая: Cisco 2611(Ethernet 1/0) -> Конвертор (Ethernet-оптика)-----ВОЛС---- Конвертор (оптика-Ethernet)<->конвертор Ethernet в G.703<->SDH<->Конвертор G.703 в Ethernet. Ошибки появляются на интерфейсе Ethernet 1/0 маршрутизатора. (если ставить к примеру комп вместо 2611, то канал идеальный с нулевыми задержками). -show interfaces ethernet 1/0 Ethernet1/0 is up, line protocol is up Hardware is AmdP2, address is 000f.9073.7750 (bia 000f.9073.7750) Internet address is 62.33.197.249/29 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 2/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:02, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 97000 bits/sec, 18 packets/sec 1819 packets input, 497512 bytes, 0 no buffer Received 1796 broadcasts, 0 runts, 0 giants, 0 throttles 1 input errors, 1 CRC, 1 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 154477 packets output, 65714787 bytes, 0 underruns 21096 output errors, 0 collisions, 11 interface resets 0 babbles, 0 late collision, 0 deferred 21096 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out -show running-config interface ethernet 1/0
Current configuration : 125 bytes ! interface Ethernet1/0 ip address 62.33.197.249 255.255.255.248 ip route-cache flow half-duplex no routing dynamic end Как избавится от lost carier? С Уважением.
|
- Ошибки lost carrier, и потери пакетов на интерфейсе., alexb, 10:55 , 06-Апр-05 (1)
А что за конвертор ? Какой у тебя Duplex на нем стоит. Попробуй поставить на int e1/0 full duplex.>Добрый день! >Уважаемые, может кто сталкивался, с чем связаны ошибки на интерфейсах lost carrier, >и как можно избавится от этого. > >Схема сети следующая: >Cisco 2611(Ethernet 1/0) -> Конвертор (Ethernet-оптика)-----ВОЛС---- Конвертор (оптика-Ethernet)<->конвертор Ethernet в G.703<->SDH<->Конвертор G.703 в Ethernet. >Ошибки появляются на интерфейсе Ethernet 1/0 маршрутизатора. (если ставить к примеру комп >вместо 2611, то канал идеальный с нулевыми задержками). > >-show interfaces ethernet 1/0 >Ethernet1/0 is up, line protocol is up > Hardware is AmdP2, address is 000f.9073.7750 (bia 000f.9073.7750) > Internet address is 62.33.197.249/29 > MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, > reliability 255/255, txload 2/255, rxload 1/255 > Encapsulation ARPA, loopback not set > Keepalive set (10 sec) > ARP type: ARPA, ARP Timeout 04:00:00 > Last input 00:00:02, output 00:00:00, output hang never > Last clearing of "show interface" counters never > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 > Queueing strategy: fifo > Output queue: 0/40 (size/max) > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 97000 bits/sec, 18 packets/sec > 1819 packets input, 497512 bytes, 0 no >buffer > Received 1796 broadcasts, 0 runts, 0 giants, >0 throttles > 1 input errors, 1 CRC, 1 frame, >0 overrun, 0 ignored > 0 input packets with dribble condition detected > > 154477 packets output, 65714787 bytes, 0 underruns > > 21096 output errors, 0 collisions, 11 interface >resets > 0 babbles, 0 late collision, 0 deferred > > 21096 lost carrier, 0 no carrier > 0 output buffer failures, 0 output buffers >swapped out > > >-show running-config interface ethernet 1/0 > >Current configuration : 125 bytes >! >interface Ethernet1/0 > ip address 62.33.197.249 255.255.255.248 > ip route-cache flow > half-duplex > no routing dynamic >end > >Как избавится от lost carier? >С Уважением.
- Ошибки lost carrier, и потери пакетов на интерфейсе., trial, 11:12 , 06-Апр-05 (2)
Конвертор D-link DMC190T Поставил Full-Duplex, ничего не изменилось. Мне кажется ошибка в маршрутизации... только вот какая не пойму... Коннектил к свитчу, пакеты ходили через тегированный порт FAst Ethernet0/0, и убегали на конвертор ,без ошибок... -#show run Building configuration...
Current configuration : 6345 bytes ! ! Last configuration change at 11:58:32 oren Wed Apr 6 2005 by 123456 ! NVRAM config last updated at 11:58:32 oren Wed Apr 6 2005 by 123456 ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname - ! boot-start-marker boot-end-marker ! clock timezone oren 5 no network-clock-participate slot 1 no network-clock-participate wic 0 ip subnet-zero ip wccp version 1 ip wccp web-cache ! ip dhcp excluded-address 192.168.2.1 ! ip dhcp pool 0 network 192.168.2.0 255.255.255.0 domain-name local dns-server 217.150.34.129 default-router 192.168.2.1 ! ip cef ip ips po max-events 100 no ip rcmd domain-lookup ip rcmd rsh-enable ip rcmd remote-host TESTER 62.165.56.162 root enable no aaa new-model no ftp-server write-enable ! controller E1 0/1 channel-group 0 timeslots 1-24 speed 64 channel-group 1 timeslots 25-31 speed 64 description ==ttk== ! class-map match-any VoIP match access-group 130 class-map match-all RTP match access-group 1 ! ! policy-map RTP class RTP priority 24 class class-default fair-queue random-detect policy-map PM_VoIP class VoIP set precedence 5 class class-default set precedence 1 ! interface Loopback1 ip address 217.150.39.244 255.255.255.255 ! interface Loopback2 ip address 62.33.197.33 255.255.255.255 ! interface Loopback3 ip address 10.200.1.73 255.255.255.252 ! interface Loopback4 ip address 62.33.197.100 255.255.255.255 ! interface Loopback6 no ip address ! interface FastEthernet0/0 no ip address ip route-cache flow speed auto half-duplex no cdp enable ! interface FastEthernet0/0.2 encapsulation dot1Q 2 ip address 192.168.2.1 255.255.255.0 secondary ip address 62.33.197.1 255.255.255.224 ip nat inside ip virtual-reassembly ! interface FastEthernet0/0.10 description == Oren-TV == encapsulation dot1Q 10 ip address 62.33.197.161 255.255.255.252 ! interface FastEthernet0/0.11 description ===ORTPZ=== encapsulation dot1Q 11 ! interface FastEthernet0/0.12 shutdown ! interface FastEthernet0/0.40 encapsulation dot1Q 40 ip address 62.33.197.197 255.255.255.252 ! interface FastEthernet0/0.41 encapsulation dot1Q 41 ip address 62.33.197.173 255.255.255.252 ! interface FastEthernet0/0.42 encapsulation dot1Q 42 ip address 62.33.197.177 255.255.255.252 ! interface FastEthernet0/0.43 encapsulation dot1Q 43 ip address 62.33.197.181 255.255.255.252 ! interface FastEthernet0/0.44 encapsulation dot1Q 44 ip address 62.33.197.185 255.255.255.252 ! interface FastEthernet0/0.45 encapsulation dot1Q 45 ip address 62.33.197.189 255.255.255.252 ! interface FastEthernet0/0.46 encapsulation dot1Q 46 ip address 62.33.197.169 255.255.255.252 no cdp enable ! interface FastEthernet0/0.47 encapsulation dot1Q 47 ip address 62.33.197.193 255.255.255.252 ! interface FastEthernet0/0.49 encapsulation dot1Q 49 ip address 62.33.197.209 255.255.255.252 ! interface FastEthernet0/0.50 encapsulation dot1Q 50 ip address 62.33.197.213 255.255.255.252 no cdp enable ! interface FastEthernet0/0.51 description ==X-plat== encapsulation dot1Q 51 ip address 192.168.134.5 255.255.255.248 secondary ip address 62.33.197.201 255.255.255.252 no cdp enable ! interface FastEthernet0/0.52 description ===TurAgenstvo=== encapsulation dot1Q 52 ip address 62.33.197.221 255.255.255.252 ! interface FastEthernet0/0.53 encapsulation dot1Q 53 ip address 62.33.197.157 255.255.255.252 ! interface FastEthernet0/0.54 description ===Buro=== encapsulation dot1Q 54 ip address 62.33.197.225 255.255.255.252 ! interface Serial0/0 ip unnumbered Loopback1 encapsulation ppp shutdown no cdp enable ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto standby ip ! interface Serial0/1:0 ip unnumbered Loopback1 ip access-group 110 in ip nat outside ip virtual-reassembly encapsulation ppp ip route-cache flow ! interface Serial0/1:1 ip unnumbered Loopback3 service-policy input PM_VoIP service-policy output PM_VoIP encapsulation ppp ip route-cache flow ! interface Ethernet1/0 ip address 62.33.197.249 255.255.255.248 ip route-cache flow full-duplex no routing dynamic ! interface Ethernet1/1 no ip address no ip mroute-cache shutdown half-duplex no cdp enable ! interface Ethernet1/2 no ip address shutdown half-duplex ! interface Ethernet1/3 ip address 192.168.0.1 255.255.255.252 ip nat inside ip virtual-reassembly full-duplex ! interface Ethernet1/3.1 ! router eigrp 1 network 62.33.197.0 0.0.0.255 auto-summary ! ip classless ip route 0.0.0.0 0.0.0.0 Serial0/1:0 ip route 62.33.197.34 255.255.255.255 62.33.197.17 ip route 62.33.197.100 255.255.255.255 FastEthernet0/1 ip route 62.33.197.248 255.255.255.248 Ethernet1/0 ip route 80.237.12.34 255.255.255.255 Serial0/1:1 ip route 80.237.13.33 255.255.255.255 Serial0/1:1 ip route 192.168.3.10 255.255.255.255 FastEthernet0/1 ! ip flow-export source FastEthernet0/0.2 ip flow-export version 5 ip flow-export destination 62.33.197.15 9992 ! no ip http server no ip http secure-server ip nat inside source list local_ofice interface Loopback2 overload ! ip access-list standard local_ofice permit 192.168.2.0 0.0.0.255 ip access-list standard squid deny 62.33.197.9 permit any ! access-list 1 permit 0.0.0.0 255.255.255.224 access-list 1 permit 62.33.197.0 0.0.0.32 access-list 110 deny tcp any any eq 135 access-list 110 deny tcp any any eq 136 access-list 110 deny tcp any any eq 137 access-list 110 deny tcp any any eq 138 access-list 110 deny tcp any any eq 139 access-list 110 deny tcp any any eq 445 access-list 110 permit ip any any access-list 130 permit ip any 80.237.12.0 0.0.1.255 snmp-server community access RW snmp-server packetsize 2046 snmp-server host 62.33.197.15 tty tty ! route-map RM_SET_RT permit 10 match ip address 130 set ip precedence critical ! ! ! control-plane ! ! line con 0 line aux 0 line vty 0 login local line vty 1 4 login line vty 5 6 login ! ntp clock-period 17180398 ntp master ntp server 195.2.64.5 ntp server 192.5.41.209 prefer ! end -#
- Ошибки lost carrier, и потери пакетов на интерфейсе., alexb, 11:37 , 06-Апр-05 (3)
К сожалению не нашел описания этого DLINK. Проблемма не в маршрутизации, у тебя ошибки на интрефейсе, а к маршрутизации это отношения не имеет. Я бы провел эксперемент возьми свич выдели на нем два порта в отдельный Vlan и подключи к ним циско E1/0 а на второй порт конвертор. Я думаю все будет замечательно работать.(если свича нет возьми хаб).Если не поможет то скорее всего это аппаратная проблемма с портом E1/0>Конвертор D-link DMC190T >Поставил Full-Duplex, ничего не изменилось. Мне кажется ошибка в маршрутизации... только вот >какая не пойму... >Коннектил к свитчу, пакеты ходили через тегированный порт FAst Ethernet0/0, и убегали >на конвертор ,без ошибок...
- Ошибки lost carrier, и потери пакетов на интерфейсе., trial, 13:02 , 06-Апр-05 (4)
>К сожалению не нашел описания этого DLINK. Проблемма не в маршрутизации, у >тебя ошибки на интрефейсе, а к маршрутизации это отношения не имеет. > >Я бы провел эксперемент возьми свич выдели на нем два порта в >отдельный Vlan и подключи к ним циско E1/0 а на второй >порт конвертор. Я думаю все будет замечательно работать.(если свича нет возьми >хаб).Если не поможет то скорее всего это аппаратная проблемма с портом >E1/0 >Интересный факт, если прокидывать на удаленное оборудование, две сети через простой хаб, (одна идет через Vlan локальная сеть из 32 адресов вторая на 8 адресов с которой проблеммы), пишешь на удаленном интерфейсе ip add *.*.*.*.* и ip addd *.*.*.* second, то канал выравнивается.
|