3.10. Cellular Phone Connection

3.10.1.1. PPP dial-up Software

3.10.1.2. Logos, Sounds, SMS, ...

If you get your mobile working via infrared, you can do some nice stuff with it. You can get informations, save your phonebook or your SMS, send SMS, put new logos (BMP format) on it, save the old logo to your harddisk and do the same with your ringtone (MIDI). To do all this nice things, you'll need the following:

• a OBEX capable mobile phone, e.g. a Siemens mobile-phone

• a working infrared connection

• the scmxx tool

• gscmxx (optional)

Bind your mobile phone to IrDA services

# irattach /dev/ttyS1 -s IrDA: Registered device irda0

Check the connection

# irdadump xid:cmd 9d5dcefa < ffffffff S=6 s=3 (14) xid:cmd 9d5dcefa < ffffffff S=6 s=4 (14) xid:rsp 9d5dcefa > 08666644 S=6 s=3 SIEMENS S35 hint=9024 [ Modem IrCOMM IrOBEX ] (28)

Show informations about your mobile phone

# scmxx -i Accessing device /dev/ircomm0 OK, a modem device is present. Vendor: SIEMENS Model: S35i Revision: 20 Serial (Phone): xxxxxxxxxxxxxxx Serial (SIM): xxxxxxxxxxxxxxx SIM-ID: xxxxxxxxxxxxxxxxxxxxx Operator: D2 SMS Server: +491722270333 Charset: GSM Battery: 40% Signal/BER: -79 dBm/? Time: 02/10/07,11:48:49 Readable Slots: bmp: 0-1, mid: 0, vcs: 1-30 Phonebooks: FD, SM, ON, ME, LD, MC, RC, OW, MS, CD, BL, RD, CS SMS storages: SM

Save your phonebook to disk

# scmxx -g -PSM -f phonebook Accessing device /dev/ircomm0 OK, a modem device is present. Detected SIEMENS S35i phonebook created. Receiving: 1 2 3 4 5 6 7 8 9 [...] Received all gettable entries

Show your SMS (here in slot 3)

# scmxx -g -S3 -f - Accessing device /dev/ircomm0 OK, a modem device is present. Detected SIEMENS S35i Looking for SMS of specified type... Receiving incoming, read SMS from slot 3. Slot: 3 From: xxxxxxxxxxxxxx Date: 2002-10-03 23:11:47 (GMT+0) SMSC number: xxxxxxxxxxxxxxxx PDU type: SMS-DELIVER MMS Data Coding Scheme: 7bit-GSM Message length: 160 Message: xxxxxxxxxxxxxxxxxxxxxxxxxx

Save your current logo to disk

# scmxx -g -B0 -f logo.bmp Accessing device /dev/ircomm0 OK, a modem device is present. Detected SIEMENS S35i Slot 0... Receiving packet 1 of 5... logo.bmp created. Receiving packet 2 of 5... Receiving packet 3 of 5... Receiving packet 4 of 5... Receiving packet 5 of 5... File transfer complete.

Save your current ringtone to disk

# scmxx -g -M0 -f sound.mid Accessing device /dev/ircomm0 OK, a modem device is present. Detected SIEMENS S35i Slot 0... Receiving packet 1 of 1... sound.mid created. File transfer complete.

3.10.3.1. Motorola

Michael McConnell has posted an initial version of a guide to get the Motorola Timeport GSM phone and Linux-IrDA talking on his website.

3.10.3.2. Ericsson

Note for T39 users (maybe for T300, too). Please check the web page of Jean Tourrilhes , you will need to apply kernel patches and tweak /proc/sys/net/irda/max_tx_window

1. Configuration To start a communication session with /dev/ircomm0 , for instance, say:

dip -t > port ircomm0 > term

Probably you may use cu or xc instead of dip, too cu -l /dev/ircomm0 or xc -l /dev/ircomm0. There are also reports about some efforts with the Ericsson GF768 and IR Modem DI 27.

Benny Amorsen wrote: The SH888 emulates an IRDA-port when you connect it using the serial cable. Why someone would think up something weird like that is beyond me, but that is the way you get it to work in Windows. Not that I ever managed to make it work in Windows, though.

Ales Dryak has send this survey (looks like a Debian/GNU Linux distribution, please modify your configuration accordingly). Mobile Ericsson SH888 ati1 = 980408 1035 PRGCXC125101:

mknod /dev/ircomm0 c 161 0 mknod /dev/ircomm1 c 161 1

2. /etc/conf.modules:

alias tty-ldisc-11 irtty alias char-major-161 ircomm-tty

3. /etc/irda/drivers: irattach /dev/ttyS0 -s # (IrDA port in SIR mode) 4. /etc/chatscripts/sh888

<ABORT stuff> "" \d\d\d\d\d\dATZE0 OK ATD<phone number to call) CONNECT \d\c

5. /etc/ppp/peers/sh888

noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/sh888" /dev/ircomm 115200 defaultroute noipdefault user <your username> # don't forget to add your password to chap secrets or chat script

A few seconds (app. 30) after executing pppd call sh888 I get connected to our Intranet/Internet having full IP connectivity (telnet, ftp, www, icmp tested). Futhermore I can connect to /dev/ircomm using minicom and play with AT command. Great! And looks stable!

3.10.3.3. NOKIA

Carlos Vidal wrote: Correct me if I'm wrong, but it seems to me that Nokia telephones do not contain a genuine hardware modem, but something which is similar in principle to WinModems for PC. Whenever Nokia writes about modem communication, they use the name "Windows software modem" (or something similar). Which is actually backed up by the need to use special Nokia software for Windows (called Nokia Cellular Data Suite).

Joonas Lehtinen wrote: This is true with 61xx models. Models: 8810, 9000(i) and 9110 should work fine. (They have inbuilt modem). My Nokia 9000 reports IrCOMM with linux.

Some suggestion by Carlos Vidal carlos_at_tarkus.se : "I'm doing some tests trying to see how far can I get with my Nokia 6110 on Linux. I've just compiled gnokii-0.2.4 [ gnokii is a tool set for Nokia mobile phones connected via serial cable for Linux and *BSD , WH], but it doesn't work [please check current gnokii , the behaviour should have been improved, there is also useful documentation about IrDA connections to phones, WH]. As I have Nokia Data Suite I did the following connection:

Nokia 6110 <-- Nokia Cable --> PC/Linux <-- Null-modem cable --> PC/W95

In the PC/Linux I run the program snooper (by Jun-ichiro itojun Itoh , sorry couldn't find an URL maybe some other sniffer will do it also, e.g. sniffit, see also appendix about serial sniffers, WH) with small modifications in order to configure the serial port correctly.

Normally, if snooper has the correct baud rate, the phone and the PC/W95 should communicate as if there was no snooper in between. This worked pretty well when I cracked the protocol of my Minolta camera. The problem here is that the phone doesn't answer or hangs after a while.

It seems that the timing is quite important during the initial phase of the communication. The log I obtain is:

0>1: UUUUUUUUUUUUUUUUUUUUUUUU line 0: LE *DTR *RTS ST SR CTS CD RI *DSR line 1: LE *DTR *RTS ST SR CTS CD RI *DSR 0>1: UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU UUUUUUUUUUUUUUU\x1e\x00\x0c\x02\x00\x09\x00\x01\x00\x0d\x00\x00\x02\x01@\x00P\x 06 1>0: \x18\x00\x00\x00\xfc\x18\x00\x00\x00\x00\x00\x00\xc0\xf0 0>1: \x1e\x00\x0c\x02\x00\x09\x00\x01\x00\x0d\x00\x00\x02\x01@\x00P\x06 1>0: \x18\x00\x00\x00\x18\x00\x00\xc0\xf0\x18\x00\x00\x00\x00\x00\x00\xc0\xf0 0>1: \x1e\x00\x0cd\x00\x06\x00\x01\x00\x10\x01`\x13\x13 1>0: \x18\x00\x00\xf0\x00\x00\xfc 0>1: \x1e\x00\x0cd\x00\x06\x00\x01\x00\x10\x01`\x13\x13

0 is the PC/95 and 1 is the phone. The communication starts with a stream of 'U' (0x55) and with DSR/DTR on. The phone answers with '0x18 0x00 ...'. This dialog continues for a while as if both were deaf and finally the phone crashes and the only way to reset it is to remove the batteries!

I guess that what happens is that the phone is trying to find the correct baud-rate and fails because of the delays introduced by snooper. This probably has to do with some IrDA protocol used with also with the infrared connection."

Wessel de Roode "I managed to get the Discovery IR hint bits (with my Palm Pilot):

Discover: 0:xxxxxxxx:81.01 01 IR_HINT_PNP 01 IR_HINT_TELEPHONY (IrMC ?) 80 IR_HINT_EXT Device info query: \006Device\012DeviceName 4e 6f 6b 69 61 20 36 31 30 30 Nokia 6100

I also managed to query the PNP device of the Nokia. It has one PNP device. It's PNPC100 which equalt a 9600 baud modem. I deleted the query, if somene can send me a hint to restore it. was somthing like IrDA:<dunno>:PNP:Comp#01 The same query with IrDA:<dunno>:PNP:CompCnt gives the number of PNP-devices are available in the Nokia. Which is here only one."

There are also reports about gsmlib for sending and receiving sms messages, updating address books etc). These functions are working, except for minor charset problems.

3.10.3.4. Siemens

Configuration By Florian Lohoff: "Do it step by step - Get your irda working irattach /dev/ttySx etc. Then have a look at the /proc/net/irda/discovery whether you find something like this:

(flo@paradigm)~# cat /proc/net/irda/discovery IrLMP: Discovery log: nickname: SIEMENS S25, hint: 0x9024, saddr: 0x4286ce23, daddr: 0x04295741

Now load ircomm and ircomm-tty and normally(tm) you should be able to connect to the correct /dev/ircomm and you can easily dial and load/backup the phonebook etc ...", e.g. with minicom.

Timo Felbinger describes the connection between a Toshiba and a Siemens S25:

• kernel 2.2.12 and patch-2.2.12-irda3, IrDA support in the kernel, ircomm and ircomm-tty as a module

• mknod /dev/ircomm0 c 161 0

• modprobe ircomm, modprobe ircomm-tty

• start irattach with modprobe toshoboe in the start section of /etc/irda/drivers . Note: don't load toshoboe before the irattach, this may cause device or resource busy

• after dip -t and the command port ircomm0 the S25 shows a connection. Note: the IR port of the S25 has to be activated of course, the distance between the two devices seems not critical.

• After term the S25 behaves like the usual Hayes modem and can be used with the AT commands.

• dial-out with pppd works out of the box.