To compile this driver into the kernel,
place the following lines in your
kernel configuration file:
device pcidevice scbusdevice amr
Alternatively, to load the driver as a
module at boot time, place the following line in
loader.conf5:
amr_load="YES"
DESCRIPTION
The
driver provides support for LSI Logic MegaRAID SCSI, ATA and SATA
RAID controllers and legacy American Megatrends MegaRAID
SCSI RAID controllers, including models relabeled
and sold by Dell and Hewlett-Packard.
LSI MegaRAID SAS controllers are supported by
mfi(4)
and will not work with this driver.
HARDWARE
Controllers supported by the
driver include:
MegaRAID SATA 150-4
MegaRAID SATA 150-6
MegaRAID SATA 300-4X
MegaRAID SATA 300-8X
MegaRAID SCSI 320-1E
MegaRAID SCSI 320-2E
MegaRAID SCSI 320-4E
MegaRAID SCSI 320-0X
MegaRAID SCSI 320-2X
MegaRAID SCSI 320-4X
MegaRAID SCSI 320-0
MegaRAID SCSI 320-1
MegaRAID SCSI 320-2
MegaRAID SCSI 320-4
MegaRAID Series 418
MegaRAID i4 133 RAID
MegaRAID Elite 1500 (Series 467)
MegaRAID Elite 1600 (Series 493)
MegaRAID Elite 1650 (Series 4xx)
MegaRAID Enterprise 1200 (Series 428)
MegaRAID Enterprise 1300 (Series 434)
MegaRAID Enterprise 1400 (Series 438)
MegaRAID Enterprise 1500 (Series 467)
MegaRAID Enterprise 1600 (Series 471)
MegaRAID Express 100 (Series 466WS)
MegaRAID Express 200 (Series 466)
MegaRAID Express 300 (Series 490)
MegaRAID Express 500 (Series 475)
Dell PERC
Dell PERC 2/SC
Dell PERC 2/DC
Dell PERC 3/DCL
Dell PERC 3/QC
Dell PERC 4/DC
Dell PERC 4/IM
Dell PERC 4/SC
Dell PERC 4/Di
Dell PERC 4e/DC
Dell PERC 4e/Di
Dell PERC 4e/Si
Dell PERC 4ei
HP NetRAID-1/Si
HP NetRAID-3/Si (D4943A)
HP Embedded NetRAID
Intel RAID Controller SRCS16
Intel RAID Controller SRCU42X
DIAGNOSTICS
Driver initialisation/shutdown phase
amr%d: memory window not available
amr%d: I/O window not available
The PCI BIOS did not allocate resources necessary for the correct operation of
the controller.
The driver cannot attach to this controller.
amr%d: busmaster bit not set, enabling
The PCI BIOS did not enable busmaster DMA,
which is required for the correct operation of the controller.
The driver has enabled this bit and initialisation will proceed.
amr%d: can't allocate register window
amr%d: can't allocate interrupt
amr%d: can't set up interrupt
amr%d: can't allocate parent DMA tag
amr%d: can't allocate buffer DMA tag
amr%d: can't allocate scatter/gather DMA tag
amr%d: can't allocate s/g table
amr%d: can't allocate mailbox tag
amr%d: can't allocate mailbox memory
A resource allocation error occurred while initialising the driver;
initialisation has failed and the driver will not attach to this controller.
amr%d: can't obtain configuration data from controller
amr%d: can't obtain product data from controller
The driver was unable to obtain vital configuration data from the controller.
Initialisation has failed and the driver will not attach to this controller.
amr%d: can't establish configuration hook
amr%d: can't scan controller for drives
The scan for logical drives managed by the controller failed.
No drives will be attached.
amr%d: device_add_child failed
amr%d: bus_generic_attach returned %d
Creation of the logical drive instances failed;
attachment of one or more logical drives may have been aborted.
amr%d: flushing cache...
The controller cache is being flushed prior to shutdown or detach.
Operational diagnostics
amr%d: I/O beyond end of unit (%u,%d > %u)
A partitioning error or disk corruption has caused an I/O request
beyond the end of the logical drive.
This may also occur if FlexRAID Virtual Sizing is enabled and
an I/O operation is attempted on a portion of the virtual drive
beyond the actual capacity available.
amr%d: polled command timeout
An initialisation command timed out.
The initialisation process may fail as a result.
amr%d: bad slot %d completed
The controller reported completion of a command that the driver did not issue.
This may result in data corruption,
and suggests a hardware or firmware problem with the system or controller.
