Партнёры:
Хостинг:
magic - file command's magic number file
Each line of the file specifies a test to be performed. A test compares the data starting at a particular offset in the file with a 1-byte, 2-byte, or 4-byte numeric value or a string. If the test succeeds, a message is printed. The line consists of the following fields:
The numeric types may optionally be followed by & and a numeric value, to specify that the value is to be AND'ed with the numeric value before any comparisons are done. Prepending a u to the type indicates that ordered comparisons should be unsigned.
Some file formats contain additional information which is to be printed along with the file type or need additional tests to determine the true file type. These additional tests are introduced by one or more > characters preceding the offset. The number of > on the line indicates the level of the test; a line with no > at the beginning is considered to be at level 0. Tests are arranged in a tree-like hierarchy: If a the test on a line at level n succeeds, all following tests at level n+1 are performed, and the messages printed if the tests succeed, untile a line with level n (or less) appears. For more complex files, one can use empty messages to get just the "if/then" effect, in the following way:
0 string MZ
>0x18 leshort <0x40 MS-DOS executable
>0x18 leshort >0x3f extended PC executable (e.g., MS Windows)
Offsets do not need to be constant, but can also be read from the file being examined. If the first character following the last > is a ( then the string after the parenthesis is interpreted as an indirect offset. That means that the number after the parenthesis is used as an offset in the file. The value at that offset is read, and is used again as an offset in the file. Indirect offsets are of the form: ((x[.[bslBSL]][+-][y]). The value of x is used as an offset in the file. A byte, short or long is read at that offset depending on the [bslBSLm] type specifier. The capitalized types interpret the number as a big endian value, whereas the small letter versions interpret the number as a little endian value; the m type interprets the number as a middle endian (PDP-11) value. To that number the value of y is added and the result is used as an offset in the file. The default type if one is not specified is long.
That way variable length structures can be examined:
# MS Windows executables are also valid MS-DOS executables
0 string MZ
>0x18 leshort <0x40 MZ executable (MS-DOS)
# skip the whole block below if it is not an extended executable
>0x18 leshort >0x3f
>>(0x3c.l) string PE\0\0 PE executable (MS-Windows)
>>(0x3c.l) string LX\0\0 LX executable (OS/2)
This strategy of examining has one drawback: You must make sure that you eventually print something, or users may get empty output (like, when there is neither PE\0\0 nor LE\0\0 in the above example)
If this indirect offset cannot be used as-is, there are simple calculations possible: appending [+-*/%&|^]<number> inside parentheses allows one to modify the value read from the file before it is used as an offset:
# MS Windows executables are also valid MS-DOS executables
0 string MZ
# sometimes, the value at 0x18 is less that 0x40 but there's still an
# extended executable, simply appended to the file
>0x18 leshort <0x40
>>(4.s*512) leshort 0x014c COFF executable (MS-DOS, DJGPP)
>>(4.s*512) leshort !0x014c MZ executable (MS-DOS)
Sometimes you do not know the exact offset as this depends on the length or position (when indirection was used before) of preceding fields. You can specify an offset relative to the end of the last uplevel field using & as a prefix to the offset:
0 string MZ
>0x18 leshort >0x3f
>>(0x3c.l) string PE\0\0 PE executable (MS-Windows)
# immediately following the PE signature is the CPU type
>>>&0 leshort 0x14c for Intel 80386
>>>&0 leshort 0x184 for DEC Alpha
Indirect and relative offsets can be combined:
0 string MZ
>0x18 leshort <0x40
>>(4.s*512) leshort !0x014c MZ executable (MS-DOS)
# if it's not COFF, go back 512 bytes and add the offset taken
# from byte 2/3, which is yet another way of finding the start
# of the extended executable
>>>&(2.s-514) string LE LE executable (MS Windows VxD driver)
Or the other way around:
0 string MZ
>0x18 leshort >0x3f
>>(0x3c.l) string LE\0\0 LE executable (MS-Windows)
# at offset 0x80 (-4, since relative offsets start at the end
# of the uplevel match) inside the LE header, we find the absolute
# offset to the code area, where we look for a specific signature
>>>(&0x7c.l+0x26) string UPX \b, UPX compressed
Or even both!
0 string MZ
>0x18 leshort >0x3f
>>(0x3c.l) string LE\0\0 LE executable (MS-Windows)
# at offset 0x58 inside the LE header, we find the relative offset
# to a data area where we look for a specific signature
>>>&(&0x54.l-3) string UNACE \b, ACE self-extracting archive
Finally, if you have to deal with offset/length pairs in your file, even the second value in a parenthesed expression can be taken from the file itself, using another set of parentheses. Note that this additional indirect offset is always relative to the start of the main indirect offset.
0 string MZ
>0x18 leshort >0x3f
>>(0x3c.l) string PE\0\0 PE executable (MS-Windows)
# search for the PE section called ".idata"...
>>>&0xf4 search/0x140 .idata
# ...and go to the end of it, calculated from start+length;
# these are located 14 and 10 bytes after the section name
>>>>(&0xe.l+(-4)) string PK\3\4 \b, ZIP self-extracting archive
|
Закладки на сайте Проследить за страницей |
Created 1996-2024 by Maxim Chirkov Добавить, Поддержать, Вебмастеру |