Video: Раньше стояла PCI с 2Mb
Сейчас поставил старушку Исашную..
Ставил Win98 тоже не работает, примерно такая же ситуация, конфликт с видео.
Досовым тестом теститься только адреса 0xa****
0xb6000, я так понимаю это как раз видео память.
2 вопроса: 1)можно ли заставить дижи работать и на старших адресах, например 0xD**** они совершенно свободны.
2)если нет то можно ли обмануть видюху, и дать поработать дижи в этих адресах (ведь в досе работает)
__
у меня есть похожая машина, тоже с дижибордом только вот там FreeBSD3.1 а у меня 4.5 но там работает, заметил в ядре видюха прописана как
device vga0 at isa? port ? conflicts
на 4.5 параметр conflict не работает.
и потом там дижи встала на 0xb4000/ впрочем вот kernel`ы
____У РАБОТАЮЩЕЙ 3.1
machine "i386"
cpu "I386_CPU"
cpu "I486_CPU"
cpu "I586_CPU"
cpu "I686_CPU"
ident ED
maxusers 128
#options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options MFS #Memory Filesystem
options MFS_ROOT #MFS usable as root device, "MFS" req'ed
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, "NFS" req'ed
options MSDOSFS #MSDOS Filesystem
options "CD9660" #ISO 9660 Filesystem
options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed
options PROCFS #Process filesystem
options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device
options UCONSOLE #Allow users to grab the console
options FAILSAFE #Be conservative
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options IPFIREWALL #firewall
options IPFIREWALL_VERBOSE #print information about
options "IPFIREWALL_VERBOSE_LIMIT=100" #limit verbosity
options IPDIVERT
options "MAXMEM=(128*1024)"
options "MAXDSIZ=(128*1024*1024)"
options "DFLDSIZ=(128*1024*1024)"
options PPP_DEFLATE
config kernel root on wd0
controller isa0
controller pci0
controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2
disk fd0 at fdc0 drive 0
options "CMD640" # work around CMD640 chip deficiency
controller wdc0 at isa? port "IO_WD1" bio irq 14
disk wd0 at wdc0 drive 0
disk wd1 at wdc0 drive 1
controller wdc1 at isa? port "IO_WD2" bio irq 15
disk wd2 at wdc1 drive 0
disk wd3 at wdc1 drive 1
options ATAPI #Enable ATAPI support for IDE bus
options ATAPI_STATIC #Don't do it as an LKM
device acd0 #IDE CD-ROM
device wfd0 #IDE Floppy (e.g. LS-120)
# A single entry for any of these controllers (ncr, ahb, ahc) is
# sufficient for any number of installed devices.
controller ahc0
controller scbus0
device da0
device cd0 #Only need one of these, the code dynamically grows
# atkbdc0 controlls both the keyboard and the PS/2 mouse
controller atkbdc0 at isa? port IO_KBD tty
device atkbd0 at isa? tty irq 1
device psm0 at isa? tty irq 12
device vga0 at isa? port ? conflicts
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? tty
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa? tty
#options XSERVER # support for X server
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
device npx0 at isa? port IO_NPX irq 13
device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4
device sio1 at isa? port "IO_COM2" tty irq 3
device sio2 at isa? disable port "IO_COM3" tty irq 5
device sio3 at isa? disable port "IO_COM4" tty irq 9
# Parallel port
device ppc0 at isa? port? net irq 7
controller ppbus0
device nlpt0 at ppbus?
device plip0 at ppbus?
device ppi0 at ppbus?
#controller vpo0 at ppbus?
# Order is important here due to intrusive probes, do *not* alphabetize
# this list of network interfaces until the probes have been fixed.
# Right now it appears that the ie0 must be probed before ep0. See
# revision 1.20 of this file.
device xl0
device ed0 at isa? port 0x320 net irq 5 iomem 0xd8000
pseudo-device loop
pseudo-device ether
pseudo-device sl 1
pseudo-device ppp 8
pseudo-device tun 8
pseudo-device pty 64
pseudo-device gzip # Exec gzipped a.out's
# KTRACE enables the system-call tracing facility ktrace(2).
# This adds 4 KB bloat to your kernel, and slightly increases
# the costs of each syscall.
#options KTRACE #kernel tracing
# This provides support for System V shared memory and message queues.
#
options SYSVSHM
options SYSVMSG
# The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be
# aware of the legal and administrative consequences of enabling this
# option. The number of devices determines the maximum number of
# simultaneous BPF clients programs runnable.
pseudo-device bpfilter 4 #Berkeley packet filter
pseudo-device snp 3
# Digiboard
device dgb0 at isa? port 0x220 iomem 0xB6000 iosiz ? tty
__у пока неработающей 4.5
machine i386
cpu I386_CPU
cpu I486_CPU
cpu I586_CPU
cpu I686_CPU
ident ED
maxusers 0
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options IPFIREWALL #firewall
options IPFIREWALL_VERBOSE #print information about
options IPFIREWALL_VERBOSE_LIMIT=100
options IPDIVERT
options PPP_DEFLATE
#options COM_ESP #code for Hayes ESP
options COM_MULTIPORT #code for some cards with shared IRQs
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
#device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
#device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
#device atapifd # ATAPI floppy drives
#device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices when
# both sym and ncr are configured
#device adv0 at isa?
#device adw
#device bt0 at isa?
#device aha0 at isa?
device aic0 at isa?
#device ncv # NCR 53C500
#device nsp # Workbit Ninja SCSI-3
#device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa? port ?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
device miibus # MII bus support
device fxp # Intel
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 8 # Kernel PPP
pseudo-device tun 8 # Packet tunnel.
pseudo-device pty 64 # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
options NDGBPORTS=8
device dgb0 at isa? port 0x320 iomem 0xb6000 iosiz ? flags 0x0
и обещанные dmesg'и
____with digiboard PC/Xe
Rebooting...
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-RELEASE #7: Thu Apr 11 20:56:27 MSD 2002
root@yandex.ru:/usr/src/sys/compile/ED
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium Pro (199.43-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 134217728 (131072K bytes)
avail memory = 127049728 (124072K bytes)
Preloaded elf kernel "kernel" at 0xc0385000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
Correcting Natoma config for non-SMP
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 ATA controller> at device 7.1 on pci0
atapci0: Busmastering DMA not supported
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xffaef000-0xffaeffff irq 11 at device 17.0 on pci0
aic7880: Single Channel A, SCSI Id=7, 16/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xef80-0xef9f mem 0xff900000-0xff9fffff,0xff5ff000-0xff5fffff irq 10 at device 18.0 on pci0
fxp0: Ethernet address 00:a0:c9:29:6d:c8
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xc0000-0xc5fff,0xc8000-0xcc7ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
dgb0: PC/Xe 64/8K (windowed)
panic: kvtop: zero page frame
Uptime: 0s
хаос...
_а теперь отключил digi в boot -c/visual
Rebooting...
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.5-RELEASE #7: Thu Apr 11 20:56:27 MSD 2002
root@yandex.ru:/usr/src/sys/compile/ED
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium Pro (199.43-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x619 Stepping = 9
Features=0xfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV>
real memory = 134217728 (131072K bytes)
FreeBSD Kernel Configuration Utility - Version 1.2
Type "help" for help or "visual" to go to the visual
configuration interface (requires MGA/VGA display or
serial terminal capable of displaying ANSI graphics).
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
Correcting Natoma config for non-SMP
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 ATA controller> at device 7.1 on pci0
atapci0: Busmastering DMA not supported
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xec00-0xecff mem 0xffaef000-0xffaeffff irq 11 at device 17.0 on pci0
aic7880: Single Channel A, SCSI Id=7, 16/255 SCBs
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xef80-0xef9f mem 0xff900000-0xff9fffff,0xff5ff000-0xff5fffff irq 10 at device 18.0 on pci0
fxp0: Ethernet address 00:a0:c9:29:6d:c8
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xc0000-0xc5fff,0xc8000-0xcc7ff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
IP packet filtering initialized, divert enabled, rule-based forwarding disabled, default to deny, logging limited to 100 packets/entry by default
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
cd0 at ahc0 bus 0 target 2 lun 0
cd0: <NEC CD-ROM DRIVE:464 1.05> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 15)
cd0: cd present [319346 x 2048 byte records]
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST15230N 0638> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da0: 4095MB (8386733 512 byte sectors: 255H 63S/T 522C)
cd1 at ahc0 bus 0 target 3 lun 0
cd1: <NEC CD-ROM DRIVE:464 1.05> Removable CD-ROM SCSI-2 device
cd1: 10.000MB/s transfers (10.000MHz, offset 15)
cd1: Attempt to query device size failed: NOT READY, Medium not present
ну я думаю теперь максимально информативно изложил проблему. Жду помощи :-)
Вариант для распечатки
OpenNET: Виртуальная конференция (Public)
on
09-Апр-02, 15:41 (MSK)
