Имеем в наличии мать Intel D865GBFL "Bayfield" (PRO/100 LAN) и процессор Intel P4-2.4/512k/800 FSB with HT, 512Мб памяти (по двум каналам) и FreeBSD 4.8 Release

Имеем две проблемы:

1. ОС упорно НЕ хочет видеть встроенную сетевую карту, хотя на мамке стоит 10/100 Mbits/sec LAN subsystem using the Intel® 82562EZ Platform LAN
Connect (PLC) device, а man fxp выводит:
The fxp driver provides support for the EtherExpress Pro/10, InBusiness 10/100, Pro/100 B, Pro/100+, Pro/100 VE, Pro/100 M, and Pro/100 S PCI Fast Ethernet adapters based on the Intel i82557, i82558, i82559, i82550, or i82562 Ethernet chips.

Т.е. карта должна видеться, но ее нет, при загрузке ОС ее находит как:
pci1: <unknown card> (vendor=0x8086, dev=0x1050) at 8.0 irq 21
или
pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 18
(одно PCI устройство вероятнее всего звук, второе наверное сетевая)

Все время использовал Intel материнки со встроенными сетевыми, никаких проблем не было (была мать на 815 и 845 чипсете, а вот на 865 чипсе какие траблы)

Сначала думал, что у меня какой-то конфликт прерывание, т.к. стоит 6 сетвых карт (1 - Интел, 2 - 3СОМ, 3 - Realtek 8139), однако вытащил ВСЕ сетевые - теже грабли.

Что делать?

2. Включил поддержку технологии НТ и получил 2-ой вритуальный процессор, вот только возникла лажа:

а) Либо работает технология НТ и SMP без поддержки apm0 в ядре.
Если включаю в ядре apm0, то при загрузке получаю:
kernel trap 12 with interrupts disabled

Fatal trap 12: page fault while in kernel mode
mp_lock = 00000001; cpuid = 0; lapic.id = 00000000
fault virtual address   = 0x66b2
fault code              = supervisor read, page not present
instruction pointer     = 0x8:0x66b2
stack pointer           = 0x10:0xd6eb1ca8
frame pointer           = 0x10:0x5310
code segment            = base 0x0, limit 0xfffff, type 0x1b
                        = DPL 0, pres 1, def32 1, gran 1
processor eflags        = resume, IOPL = 0
current process         = Idle
interrupt mask          = none <- SMP: XXX
trap number             = 12
panic: page fault
mp_lock = 00000001; cpuid = 0; lapic.id = 00000000
boot() called on cpu#0

syncing disks...

б) Либо если выключаю поддержку HT и SMP, и включаю в ядре apm0, то получаю прекрасно работающий apm0 (питание выключает по shutdown -p)

Как их заставить работать вместе?!

Заранее ВСЕМ спасибо!

P.S. dmesg
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RELEASE #8: Sun Jul  6 08:34:03 EEST 2003
    root@Server.SoHo.NET.ua:/usr/src/sys/compile/SOHO.NEW
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2394.16-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 534970368 (522432K bytes)
avail memory = 517754880 (505620K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id:  0, version: 0x00050014, at 0xfee00000
cpu1 (AP):  apic id:  1, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id:  2, version: 0x00178020, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc02bd000.
Pentium Pro MTRR support enabled
Using $PIR table, 12 entries at 0xc00f3310
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #0 intpin 16 -> irq 2
IOAPIC #0 intpin 19 -> irq 16
IOAPIC #0 intpin 18 -> irq 17
IOAPIC #0 intpin 17 -> irq 18
pci0: <PCI bus> on pcib0
pci0: <Intel model 2572 VGA-compatible display device> at 2.0 irq 2
pci0: <UHCI USB controller> at 29.0 irq 2
pci0: <UHCI USB controller> at 29.1 irq 16
pci0: <UHCI USB controller> at 29.2 irq 17
pci0: <UHCI USB controller> at 29.3 irq 2
pcib1: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
IOAPIC #0 intpin 21 -> irq 19
IOAPIC #0 intpin 22 -> irq 20
IOAPIC #0 intpin 20 -> irq 21
pci1: <PCI bus> on pcib1
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xcc00-0xcc3f mem 0xff700000-0xff7fffff,0xff8ff000-0xff8fffff irq 19 at device 0.0 on pci1
fxp0: Ethernet address 00:90:27:a3:ac:ff
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xc800-0xc87f mem 0xff8fec00-0xff8fec7f irq 20 at device 1.0 on pci1
xl0: Ethernet address: 00:04:76:e7:32:2b
miibus1: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus1
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl1: <3Com 3c900-COMBO Etherlink XL> port 0xc400-0xc43f irq 18 at device 2.0 on pci1
xl1: Ethernet address: 00:10:5a:ba:6a:b7
xl1: selecting 10baseT transceiver, half duplex
rl0: <RealTek 8139 10/100BaseTX> port 0xc000-0xc0ff mem 0xff8fe800-0xff8fe8ff irq 16 at device 3.0 on pci1
rl0: Ethernet address: 00:30:4f:23:d8:9e
miibus2: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus2
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl1: <RealTek 8139 10/100BaseTX> port 0xb800-0xb8ff mem 0xff8fe400-0xff8fe4ff irq 17 at device 4.0 on pci1
rl1: Ethernet address: 00:30:4f:23:f5:81
miibus3: <MII bus> on rl1
rlphy1: <RealTek internal media interface> on miibus3
rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl2: <RealTek 8139 10/100BaseTX> port 0xb400-0xb4ff mem 0xff8fe000-0xff8fe0ff irq 18 at device 5.0 on pci1
rl2: Ethernet address: 00:30:4f:1b:ab:85
miibus4: <MII bus> on rl2
rlphy2: <RealTek internal media interface> on miibus4
rlphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci1: <unknown card> (vendor=0x8086, dev=0x1050) at 8.0 irq 21
isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port 0xffa0-0xffaf,0-0x3,0-0x7,0-0x3,0-0x7 irq 17 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 18
orm0: <Option ROMs> at iomem 0xca800-0xcb7ff,0xcb800-0xcbfff,0xcc000-0xccfff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
DUMMYNET initialized (011031)
IP packet filtering initialized, divert disabled, rule-based forwarding enabled, default to deny, logging limited to 1000 packets/entry by default
SMP: AP CPU #1 Launched!
ad0: 38204MB <SAMSUNG SV4012H> [77622/16/63] at ata0-master BIOSDMA
Mounting root from ufs:/dev/ad0s1a
xl1: selecting BNC port, half duplex