>Проблема такая: при установке Win XP система распознала мою сетевую карту (D-Link
>DFE-530TX) как ethernet-контроллер. Я в инете скачал СООТВЕТСТВУЮЩИЕ драйвера и
>разархивировал их на жёсткий диск. В диспетчере устройств удалил ethernet-контроллер и
>попытался установить через "установку оборудования" сетевую карту, при этом указав точную
>дирректорию где хранятся скаченные драйвера (кстати там несколько драйверов), система их
>не распознаёт и опять устанавливает ethernet-контроллер. Удалял и устанавливал несколько раз
>при наличии подключённого коннектора и без него, перегружал комп. Ничего не
>помогает.
>Кто знает, помогите мне разгодать эту загатку.
>Заранее благодарю и ещё если не трудно по ходу скиньте свои мнения
>мне на Е-mail.
А в чем загадка то? Не работает, или что?
Вот, что они сами пишут на компашке в каталоге WINXP:
D-Link DFE-530TX PCI Fast Ethernet Adapter Installation
for Windows XP
Getting Started
---------------
The Windows XP installation CD are needed to complete this install.
Windows XP build-in driver Installation Procedure
(for rev.A, B card)
-------------------------------------------------
1. Plug PCI Ethernet adapter into the system.
2. Start your PC normally. Upon power up, the system will
indicate to you that "new network device installed".
Windows has detected the installation of a new networking
device and completed installation procedure. If you want
to setup up a network, click the icon to run the network
setup wizard.
Windows XP update Driver Installation Procedure
(for rev.A, B card)
-----------------------------------------------
1. Make sure your computer is power-off.
2. Plug the adapter into one PCI slot of your computer.
3. Turn on the power. Your computer should be booting.
4. Windows XP will find new hardware, and install
"D-Link DFE-530TX PCI Fast Ethernet Adapter (rev.A)" or
"D-Link DFE-530TX PCI Fast Ethernet Adapter (rev.B)"
automatically.
5. Click "Start" --> right click "My Computer" and select
"Properties".
6. Select "Hardware" --> "Device Manager".
7. Right click "D-Link DFE-530TX PCI Fast Ethernet Adapter..." in Network Adapters
and select "Update Driver...".
8. Check "install from a list or specific location (Advance), click Next.
9. Check "Don't search. I will choose the driver to install", click Next.
10. Click "Have Disk..." and specific location A:\, if driver
in floppy disk. (assum D:\ for CD-ROM) Click "OK" for next.
11. Select "D-Link DFE-530TX PCI Fast Ethernet Adapter..." and click Next.
Then will copy driver files into system.
12. Please select "Continue Anyway" to finish the installation.
13 After finishing the installation, there should be a new
'Local Area Connection' will appear and the LAN card should works now.
Windows XP new Driver Installation Procedure
(for rev.C card)
-----------------------------------------------
The following steps helps you install driver for your adapter:
1. Make sure your computer is power-off.
2. Plug the adapter into one PCI slot of your computer.
3. Turn on the power. Your computer should be booting.
4. Windows XP will find new hardware, and
"Add new hardware wizard" will appear.
5. Insert the driver diskette/CD into floppy/CDROM drive.
6. Follow the instruction and the wizard will help you
complete the installation.
Trouble Shooting
----------------
1. Everything is OK in Device Manager, but the network adapter still
doesn't function properly. Please make sure that your Computer
name is different from others in the same network. You can change
your Computer name in
"My Computer" -> Press right key of you mouse and select "Properties"->
"Computer Name" -> "Change" icons
2. Everything appears to be OK but the network adapter still doesn't
function properly. Please make sure that the adapter is properly
connected to a network device (ex: HUB) and the "connection type"
for this adapter is set to "Auto-negotiation" or the correct
media type. You can check it in "My Computer" -> press right key of
your mouse and select "properties"->"Device Manager"->"Network Adapter"
-> "Properties" icons. Select "Advanced" item.
Driver keywords:
----------------
Open "Device Manager" -> "Network Adapter" -> "Properties" ->
Double click "D-Link DFE-530TX ...", Select "Advanced" item.
Connection Type Specify the connection type for the adapter.
Default: Auto-Negotiation
Flow Control Flow control capability advertisement.
Default: Hardware Default
(Not supported in force mode)
Network Address You can set the Ethernet address for your
adapter. It is not recommended to use this
keyword. As you know two or more adapter in
the same network with same Ethernet address
will cause a little problem.
When using this keyword you need to input
exactly 6 bytes of Ethernet address using
one of the following format:
xxxxxxxxxxxx
Default: read address from adapter ROM.
Transmit Buffers Internal driver buffers for packet transmit.
Default: 64
Receive Buffers Internal driver buffers for packet receive.
Default: 64
Validate Packet Length Enable driver to check packet length.
If packet length is incorrect, the driver
will drop this packet.
Default: Disable
Вариант для распечатки
OpenNET: Виртуальная конференция (Public)
on
25-Фев-04, 03:50 (MSK)
