key "rndc-key" {
algorithm hmac-md5;
secret "/ANxwmSkbyH8iBYBERPcvQ==";
};controls {
inet 127.0.0.1 port 53 //953
allow { 127.0.0.1; } keys { "rndc-key"; };
};
acl "corpnets" { 192.168.255.0/24; 127.0.0.1;};
// $FreeBSD: src/etc/namedb/named.conf,v 1.6.2.7 2003/02/13 13:16:51 keramida Exp $
// Refer to the named.conf(5) and named(8) man pages for details.
options {
directory "/etc/namedb";
pid-file "/var/run/named.pid";
allow-query { any; };
listen-on {any; };
// In addition to the "forwarders" clause, you can force your name
// server to never initiate queries of its own, but always ask its
// forwarders only, by enabling the following line:
//
// forward only;
// If you've got a DNS server around at your upstream provider, enter
// its IP address here, and enable the line below. This will make you
// benefit from its cache, thus reduce overall DNS traffic in the Internet.
// forwarders {
// 213.179.232.78; //sirius primary DNS
// 195.5.6.10; //sirius DNS
// 127.0.0.1;
// };
/*
* If there is a firewall between you and nameservers you want
* to talk to, you might need to uncomment the query-source
* directive below. Previous versions of BIND always asked
* questions using port 53, but BIND 8.1 uses an unprivileged
* port by default.
*/
query-source address * port 53;
/*
* If running in a sandbox, you may have to specify a different
* location for the dumpfile.
*/
// dump-file "s/named_dump.db";
};
// Note: the following will be supported in a future release.
/*
host { any; } {
topology {
127.0.0.0/8;
};
};
*/
// Setting up secondaries is way easier and a rough example for this
// is provided below.
//
// If you enable a local name server, don't forget to enter 127.0.0.1
// first in your /etc/resolv.conf so this server will be queried.
// Also, make sure to enable it in /etc/rc.conf.
zone "." {
type hint;
file "named.root";
};
zone "0.0.127.IN-ADDR.ARPA" in {
type master;
file "localhost.rev";
notify no;
};
#zone "ipst.zt.ukrtel.net" {
# type master;
# file "ipst.host";
#};
zone "ipst.edu.ua" in {
type master;
file "ipst.edu.host";
notify yes;
allow-transfer {195.24.128.164;};
};
// RFC 3152
zone "1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.IP6.ARPA" {
type master;
file "localhost.rev";
};
// RFC 1886 -- deprecated
/*zone "1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.IP6.INT" {
type master;
file "localhost-v6.rev";
};
*/
// NB: Do not use the IP addresses below, they are faked, and only
// serve demonstration/documentation purposes!
//
// Example secondary config entries. It can be convenient to become
// a secondary at least for the zone your own domain is in. Ask
// your network administrator for the IP address of the responsible
// primary.
//
// Never forget to include the reverse lookup (IN-ADDR.ARPA) zone!
// (This is named after the first bytes of the IP address, in reverse
// order, with ".IN-ADDR.ARPA" appended.)
//
// Before starting to set up a primary zone, make sure you fully
// understand how DNS and BIND works. There are sometimes
// non-obvious pitfalls. Setting up a secondary is simpler.
//
// NB: Don't blindly enable the examples below. :-) Use actual names
// and addresses instead.
//
// NOTE!!! FreeBSD can run bind in a sandbox (see named_flags in rc.conf).
// The directory containing the secondary zones must be write accessible
// to bind. The following sequence is suggested:
//
// mkdir /etc/namedb/s
// chown bind:bind /etc/namedb/s
// chmod 750 /etc/namedb/s
/*
zone "domain.com" {
type slave;
file "s/domain.com.bak";
masters {
192.168.1.1;
};
};
zone "0.168.192.in-addr.arpa" {
type slave;
file "s/0.168.192.in-addr.arpa.bak";
masters {
192.168.1.1;
};
};
*/