The OpenNET Project / Index page

[ новости /+++ | форум | теги | ]

форумы  помощь  поиск  регистрация  майллист  вход/выход  слежка  RSS
"Xfce4 на OpenBSD не грузится"
Вариант для распечатки  
Пред. тема | След. тема 
Форум Открытые системы на рабочей станции (icewm, xfce... / Другая система)
Изначальное сообщение [ Отслеживать ]

"Xfce4 на OpenBSD не грузится"  +/
Сообщение от vlalin (ok) on 22-Ноя-12, 16:11 
Добрый день!

Прочитав статью в Хакере "укрощение строптивой", решил установить на своем Acer 1830T OpenBSD в качестве десктопа. Будучи в никсах нубом, загрузочную флешку не осилил сделать, но удалось поставить по PXE. Ставил OpenBSD 5.0. Система работает, но без X-ов. Следуя журналу, выкачал необходимые пакеты, нажал startxfce и получил черный экран без всяких ошибок.

egrep 'EE|WW' /var/log/Xorg.1.log выдает следующее:

(WW) Falling back to old probe method for vesa
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(EE) XKB: Couldn't open rules file /usr/X11R6/share/X11/xkb/rules/base


Полный лог Xorg.1.log:


[3392298.625] (--) checkDevMem: using aperture driver /dev/xf86
[3392298.643] (--) Using wscons driver on /dev/ttyC4 in pcvt compatibility mode (version 3.32)
[3392298.682]
X.Org X Server 1.9.5
Release Date: 2011-03-17
[3392298.682] X Protocol Version 11, Revision 0
[3392298.682] Build Operating System: OpenBSD 5.0 i386
[3392298.682] Current Operating System: OpenBSD vlalin.my.domain 5.0 GENERIC.MP#59 i386
[3392298.682] Build Date: 11 August 2011  10:14:19AM
[3392298.682]  
[3392298.682] Current version of pixman: 0.22.2
[3392298.682]     Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
[3392298.683] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[3392298.683] (==) Log file: "/var/log/Xorg.1.log", Time: Sun Nov  4 10:53:49 2012
[3392298.726] (II) Loader magic: 0x3c028cc0
[3392298.726] (II) Module ABI versions:
[3392298.726]     X.Org ANSI C Emulation: 0.4
[3392298.726]     X.Org Video Driver: 8.0
[3392298.726]     X.Org XInput driver : 11.0
[3392298.726]     X.Org Server Extension : 4.0
[3392298.727] (--) PCI:*(0:0:2:0) 8086:0046:1025:040e rev 2, Mem @ 0x90000000/4194304, 0x80000000/268435456, I/O @ 0x00003050/8
[3392298.727] (==) Using default built-in configuration (21 lines)
[3392298.727] (==) --- Start of built-in configuration ---
[3392298.727]     Section "Device"
[3392298.727]         Identifier    "Builtin Default intel Device 0"
[3392298.727]         Driver    "intel"
[3392298.727]     EndSection
[3392298.727]     Section "Screen"
[3392298.728]         Identifier    "Builtin Default intel Screen 0"
[3392298.728]         Device    "Builtin Default intel Device 0"
[3392298.728]     EndSection
[3392298.728]     Section "Device"
[3392298.728]         Identifier    "Builtin Default vesa Device 0"
[3392298.728]         Driver    "vesa"
[3392298.728]     EndSection
[3392298.728]     Section "Screen"
[3392298.728]         Identifier    "Builtin Default vesa Screen 0"
[3392298.728]         Device    "Builtin Default vesa Device 0"
[3392298.728]     EndSection
[3392298.728]     Section "ServerLayout"
[3392298.728]         Identifier    "Builtin Default Layout"
[3392298.728]         Screen    "Builtin Default intel Screen 0"
[3392298.728]         Screen    "Builtin Default vesa Screen 0"
[3392298.728]     EndSection
[3392298.728] (==) --- End of built-in configuration ---
[3392298.729] (==) ServerLayout "Builtin Default Layout"
[3392298.729] (**) |-->Screen "Builtin Default intel Screen 0" (0)
[3392298.729] (**) |   |-->Monitor "<default monitor>"
[3392298.730] (**) |   |-->Device "Builtin Default intel Device 0"
[3392298.730] (==) No monitor specified for screen "Builtin Default intel Screen 0".
    Using a default monitor configuration.
[3392298.730] (**) |-->Screen "Builtin Default vesa Screen 0" (1)
[3392298.730] (**) |   |-->Monitor "<default monitor>"
[3392298.730] (**) |   |-->Device "Builtin Default vesa Device 0"
[3392298.730] (==) No monitor specified for screen "Builtin Default vesa Screen 0".
    Using a default monitor configuration.
[3392298.730] (==) Disabling SIGIO handlers for input devices
[3392298.730] (==) Automatically adding devices
[3392298.730] (==) Automatically enabling devices
[3392298.889] (==) FontPath set to:
    /usr/X11R6/lib/X11/fonts/misc/,
    /usr/X11R6/lib/X11/fonts/TTF/,
    /usr/X11R6/lib/X11/fonts/OTF/,
    /usr/X11R6/lib/X11/fonts/Type1/,
    /usr/X11R6/lib/X11/fonts/100dpi/,
    /usr/X11R6/lib/X11/fonts/75dpi/
[3392298.889] (==) ModulePath set to "/usr/X11R6/lib/modules"
[3392298.889] (II) The server relies on wscons to provide the list of input devices.
    If no devices become available, reconfigure wscons or disable AutoAddDevices.
[3392298.889] (II) LoadModule: "extmod"
[3392298.925] (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.so
[3392298.929] (II) Module extmod: vendor="X.Org Foundation"
[3392298.929]     compiled for 1.9.5, module version = 1.0.0
[3392298.929]     Module class: X.Org Server Extension
[3392298.929]     ABI class: X.Org Server Extension, version 4.0
[3392298.929] (II) Loading extension MIT-SCREEN-SAVER
[3392298.929] (II) Loading extension XFree86-VidModeExtension
[3392298.929] (II) Loading extension XFree86-DGA
[3392298.929] (II) Loading extension DPMS
[3392298.929] (II) Loading extension XVideo
[3392298.930] (II) Loading extension XVideo-MotionCompensation
[3392298.930] (II) Loading extension X-Resource
[3392298.930] (II) LoadModule: "dbe"
[3392298.931] (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.so
[3392298.932] (II) Module dbe: vendor="X.Org Foundation"
[3392298.932]     compiled for 1.9.5, module version = 1.0.0
[3392298.932]     Module class: X.Org Server Extension
[3392298.932]     ABI class: X.Org Server Extension, version 4.0
[3392298.932] (II) Loading extension DOUBLE-BUFFER
[3392298.932] (II) LoadModule: "glx"
[3392298.939] (II) Loading /usr/X11R6/lib/modules/extensions/libglx.so
[3392298.941] (II) Module glx: vendor="X.Org Foundation"
[3392298.941]     compiled for 1.9.5, module version = 1.0.0
[3392298.941]     ABI class: X.Org Server Extension, version 4.0
[3392298.942] (==) AIGLX enabled
[3392298.942] (II) Loading extension GLX
[3392298.942] (II) LoadModule: "record"
[3392298.943] (II) Loading /usr/X11R6/lib/modules/extensions/librecord.so
[3392298.948] (II) Module record: vendor="X.Org Foundation"
[3392298.948]     compiled for 1.9.5, module version = 1.13.0
[3392298.948]     Module class: X.Org Server Extension
[3392298.948]     ABI class: X.Org Server Extension, version 4.0
[3392298.948] (II) Loading extension RECORD
[3392298.948] (II) LoadModule: "dri"
[3392298.949] (II) Loading /usr/X11R6/lib/modules/extensions/libdri.so
[3392298.966] (II) Module dri: vendor="X.Org Foundation"
[3392298.966]     compiled for 1.9.5, module version = 1.0.0
[3392298.966]     ABI class: X.Org Server Extension, version 4.0
[3392298.967] (II) Loading extension XFree86-DRI
[3392298.967] (II) LoadModule: "dri2"
[3392298.968] (II) Loading /usr/X11R6/lib/modules/extensions/libdri2.so
[3392298.969] (II) Module dri2: vendor="X.Org Foundation"
[3392298.969]     compiled for 1.9.5, module version = 1.2.0
[3392298.969]     ABI class: X.Org Server Extension, version 4.0
[3392298.969] (II) Loading extension DRI2
[3392298.969] (II) LoadModule: "intel"
[3392298.970] (II) Loading /usr/X11R6/lib/modules/drivers/intel_drv.so
[3392298.990] (II) Module intel: vendor="X.Org Foundation"
[3392298.991]     compiled for 1.9.5, module version = 2.9.1
[3392298.991]     Module class: X.Org Video Driver
[3392298.991]     ABI class: X.Org Video Driver, version 8.0
[3392298.999] (II) LoadModule: "vesa"
[3392299.000] (II) Loading /usr/X11R6/lib/modules/drivers/vesa_drv.so
[3392299.001] (II) Module vesa: vendor="X.Org Foundation"
[3392299.001]     compiled for 1.9.5, module version = 2.3.0
[3392299.001]     Module class: X.Org Video Driver
[3392299.001]     ABI class: X.Org Video Driver, version 8.0
[3392299.001] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
    i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
    E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
    965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
    4 Series, G45/G43, Q45/Q43, G41, B43, Clarkdale, Arrandale
[3392299.001] (II) VESA: driver for VESA chipsets: vesa
[3392299.005] (WW) Falling back to old probe method for vesa
[3392299.005] (II) Loading sub module "vgahw"
[3392299.005] (II) LoadModule: "vgahw"
[3392299.008] (II) Loading /usr/X11R6/lib/modules/libvgahw.so
[3392299.019] (II) Module vgahw: vendor="X.Org Foundation"
[3392299.019]     compiled for 1.9.5, module version = 0.1.0
[3392299.019]     ABI class: X.Org Video Driver, version 8.0
[3392299.019] (II) Loading sub module "ramdac"
[3392299.019] (II) LoadModule: "ramdac"
[3392299.019] (II) Module "ramdac" already built-in
[3392299.020] drmOpenDevice: node name is /dev/drm0
[3392299.020] drmOpenDevice: open result is 10, (OK)
[3392299.020] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[3392299.020] drmOpenDevice: node name is /dev/drm0
[3392299.020] drmOpenDevice: open result is 10, (OK)
[3392299.020] drmOpenByBusid: drmOpenMinor returns 10
[3392299.020] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[3392299.020] (II) intel(0): Creating default Display subsection in Screen section
    "Builtin Default intel Screen 0" for depth/fbbpp 24/32
[3392299.020] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[3392299.020] (==) intel(0): RGB weight 888
[3392299.020] (==) intel(0): Default visual is TrueColor
[3392299.020] (II) intel(0): Integrated Graphics Chipset: Intel(R) Arrandale
[3392299.020] (--) intel(0): Chipset: "Arrandale"
[3392299.020] (--) intel(0): Linear framebuffer at 0x80000000
[3392299.020] (--) intel(0): IO registers at addr 0x90000000 size 4194304
[3392299.020] (WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
[3392299.021] (II) intel(0): No SDVO device is found in VBT
[3392299.021] (II) intel(0): 2 display pipes available.
[3392299.021] (II) Loading sub module "ddc"
[3392299.021] (II) LoadModule: "ddc"
[3392299.021] (II) Module "ddc" already built-in
[3392299.021] (II) Loading sub module "i2c"
[3392299.021] (II) LoadModule: "i2c"
[3392299.021] (II) Module "i2c" already built-in
[3392299.021] (II) intel(0): Output VGA has no monitor section
[3392299.021] (II) intel(0): Output LVDS has no monitor section
[3392299.021] (II) intel(0): I2C bus "LVDSDDC_C" initialized.
[3392299.021] (II) intel(0): Attempting to determine panel fixed mode.
[3392299.021] (II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
[3392299.082] (II) intel(0): EDID for output LVDS
[3392299.082] (II) intel(0): Manufacturer: AUO  Model: 205c  Serial#: 0
[3392299.082] (II) intel(0): Year: 2008  Week: 1
[3392299.082] (II) intel(0): EDID Version: 1.3
[3392299.082] (II) intel(0): Digital Display Input
[3392299.082] (II) intel(0): Max Image Size [cm]: horiz.: 26  vert.: 14
[3392299.082] (II) intel(0): Gamma: 2.20
[3392299.082] (II) intel(0): No DPMS capabilities specified
[3392299.082] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[3392299.082] (II) intel(0): First detailed timing is preferred mode
[3392299.082] (II) intel(0): redX: 0.584 redY: 0.333   greenX: 0.338 greenY: 0.571
[3392299.082] (II) intel(0): blueX: 0.158 blueY: 0.133   whiteX: 0.313 whiteY: 0.329
[3392299.082] (II) intel(0): Manufacturer's mask: 0
[3392299.082] (II) intel(0): Supported detailed timing:
[3392299.082] (II) intel(0): clock: 65.5 MHz   Image Size:  256 x 144 mm
[3392299.082] (II) intel(0): h_active: 1366  h_sync: 1390  h_sync_end 1406 h_blank_end 1406 h_border: 0
[3392299.082] (II) intel(0): v_active: 768  v_sync: 770  v_sync_end 774 v_blanking: 776 v_border: 0
[3392299.082] (II) intel(0): Unknown vendor-specific block f
[3392299.082] (II) intel(0):  AUO
[3392299.082] (II) intel(0):  B116XW02 V0
[3392299.082] (II) intel(0): EDID (in hex):
[3392299.082] (II) intel(0):     00ffffffffffff0006af5c2000000000
[3392299.083] (II) intel(0):     01120103801a0e780a99859555569228
[3392299.083] (II) intel(0):     22505400000001010101010101010101
[3392299.083] (II) intel(0):     01010101010196195628500008301810
[3392299.083] (II) intel(0):     24000090100000180000000f00000000
[3392299.083] (II) intel(0):     00000000000000000020000000fe0041
[3392299.083] (II) intel(0):     554f0a202020202020202020000000fe
[3392299.083] (II) intel(0):     004231313658573032205630200a00f8
[3392299.083] (II) intel(0): EDID vendor "AUO", prod id 8284
[3392299.083] (II) intel(0): Output HDMI-3 has no monitor section
[3392299.083] (II) intel(0): I2C bus "HDMIB" initialized.
[3392299.083] (II) intel(0): HDMI-3 output detected
[3392299.099] (II) intel(0): EDID for output VGA
[3392299.159] (II) intel(0): EDID for output LVDS
[3392299.159] (II) intel(0): Manufacturer: AUO  Model: 205c  Serial#: 0
[3392299.159] (II) intel(0): Year: 2008  Week: 1
[3392299.159] (II) intel(0): EDID Version: 1.3
[3392299.159] (II) intel(0): Digital Display Input
[3392299.159] (II) intel(0): Max Image Size [cm]: horiz.: 26  vert.: 14
[3392299.159] (II) intel(0): Gamma: 2.20
[3392299.159] (II) intel(0): No DPMS capabilities specified
[3392299.159] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[3392299.159] (II) intel(0): First detailed timing is preferred mode
[3392299.159] (II) intel(0): GTF timings supported
[3392299.159] (II) intel(0): redX: 0.584 redY: 0.333   greenX: 0.338 greenY: 0.571
[3392299.159] (II) intel(0): blueX: 0.158 blueY: 0.133   whiteX: 0.313 whiteY: 0.329
[3392299.159] (II) intel(0): Manufacturer's mask: 0
[3392299.159] (II) intel(0): Supported detailed timing:
[3392299.159] (II) intel(0): clock: 65.5 MHz   Image Size:  256 x 144 mm
[3392299.159] (II) intel(0): h_active: 1366  h_sync: 1390  h_sync_end 1406 h_blank_end 1406 h_border: 0
[3392299.159] (II) intel(0): v_active: 768  v_sync: 770  v_sync_end 774 v_blanking: 776 v_border: 0
[3392299.159] (II) intel(0): Ranges: V min: 0 V max: 200 Hz, H min: 0 H max: 200 kHz,
[3392299.159] (II) intel(0):  AUO
[3392299.159] (II) intel(0):  B116XW02 V0
[3392299.159] (II) intel(0): EDID (in hex):
[3392299.159] (II) intel(0):     00ffffffffffff0006af5c2000000000
[3392299.159] (II) intel(0):     01120103801a0e780a99859555569228
[3392299.159] (II) intel(0):     22505400000001010101010101010101
[3392299.159] (II) intel(0):     01010101010196195628500008301810
[3392299.159] (II) intel(0):     24000090100000180000000f00000000
[3392299.159] (II) intel(0):     00000000000000000020000000fe0041
[3392299.159] (II) intel(0):     554f0a202020202020202020000000fe
[3392299.159] (II) intel(0):     004231313658573032205630200a00f8
[3392299.159] (II) intel(0): EDID vendor "AUO", prod id 8284
[3392299.159] (II) intel(0): Printing probed modes for output LVDS
[3392299.159] (II) intel(0): Modeline "1366x768"x60.0   65.50  1366 1390 1406 1406  768 770 774 776 -hsync -vsync (46.6 kHz)
[3392299.159] (II) intel(0): I2C device "HDMIB:ddc2" registered at address 0xA0.
[3392299.163] (II) intel(0): EDID for output HDMI-3
[3392299.163] (II) intel(0): EDID for output HDMI-3
[3392299.163] (II) intel(0): Output VGA disconnected
[3392299.163] (II) intel(0): Output LVDS connected
[3392299.163] (II) intel(0): Output HDMI-3 disconnected
[3392299.163] (II) intel(0): Using exact sizes for initial modes
[3392299.163] (II) intel(0): Output LVDS using initial mode 1366x768
[3392299.163] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[3392299.163] (II) intel(0): detected 512 kB GTT.
[3392299.163] (II) intel(0): detected 131068 kB stolen memory.
[3392299.163] (==) intel(0): video overlay key set to 0x101fe
[3392299.164] (==) intel(0): DPI set to (96, 96)
[3392299.164] (II) Loading sub module "fb"
[3392299.164] (II) LoadModule: "fb"
[3392299.165] (II) Loading /usr/X11R6/lib/modules/libfb.so
[3392299.183] (II) Module fb: vendor="X.Org Foundation"
[3392299.183]     compiled for 1.9.5, module version = 1.0.0
[3392299.183]     ABI class: X.Org ANSI C Emulation, version 0.4
[3392299.183] (II) Loading sub module "int10"
[3392299.183] (II) LoadModule: "int10"
[3392299.184] (II) Loading /usr/X11R6/lib/modules/libint10.so
[3392299.186] (II) Module int10: vendor="X.Org Foundation"
[3392299.186]     compiled for 1.9.5, module version = 1.0.0
[3392299.186]     ABI class: X.Org Video Driver, version 8.0
[3392299.186] (==) intel(0): Write-combining range (0xa0000,0x20000) was already clear
[3392299.189] (==) intel(0): Removed Write-combining range (0xc0000,0x40000)
[3392299.198] (II) intel(0): Bad V_BIOS checksum
[3392299.198] (II) intel(0): Primary V_BIOS segment is: 0xc000
[3392299.198] (==) intel(0): Write-combining range (0x0,0x1000) was already clear
[3392299.199] (--) intel(0): Console VGA mode is 0x3
[3392299.200] (II) UnloadModule: "vesa"
[3392299.200] (II) Unloading /usr/X11R6/lib/modules/drivers/vesa_drv.so
[3392299.200] (==) Depth 24 pixmap format is 32 bpp
[3392299.200] (II) intel(0): Kernel reported 491520 total, 0 used
[3392299.200] (II) intel(0): I830CheckAvailableMemory: 1966080 kB available
[3392299.201] (II) intel(0): [DRI2] Setup complete
[3392299.201] (II) intel(0): [DRI2]   DRI driver: i965
[3392299.201] (**) intel(0): Framebuffer compression disabled
[3392299.201] (**) intel(0): Tiling enabled
[3392299.201] (**) intel(0): SwapBuffers wait enabled
[3392299.205] (==) intel(0): VideoRam: 262144 KB
[3392299.205] (II) intel(0): Attempting memory allocation with tiled buffers.
[3392299.205] (II) intel(0): Tiled allocation successful.
[3392299.205] (II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
[3392299.205] (==) intel(0): Write-combining range (0xa0000,0x10000) was already clear
[3392299.228] (II) UXA(0): Driver registered support for the following operations:
[3392299.228] (II)         solid
[3392299.228] (II)         copy
[3392299.228] (II)         composite (RENDER acceleration)
[3392299.228] (II)         put_image
[3392299.228] (II)         get_image
[3392299.229] (==) intel(0): Backing store disabled
[3392299.229] (==) intel(0): Silken mouse disabled
[3392299.242] (II) intel(0): Initializing HW Cursor
[3392299.604] Plane disable
[3392299.644] Pipe disable
[3392299.684] PFIT disable
[3392299.684] FDI TX disable
[3392299.684] FDI RX disable
[3392299.704] FDI TX train 1 preload
[3392299.704] FDI RX train 1 preload
[3392299.724] LVDS port force off
[3392299.724] Transcoder disable
[3392299.764] PCH DPLL disable
[3392299.764] FDI RX PLL PCD disable
[3392299.764] FDI TX PLL disable 001a2040
[3392299.784] FDI RX PLL disable 001c4000
[3392299.804] DPMS off done
[3392299.824] Plane disable
[3392299.824] Pipe disable
[3392299.844] PFIT disable
[3392299.844] FDI TX disable
[3392299.844] FDI RX disable
[3392299.864] FDI TX train 1 preload
[3392299.864] FDI RX train 1 preload
[3392299.884] LVDS port force off
[3392299.884] Transcoder disable
[3392299.904] PCH DPLL disable
[3392299.904] FDI RX PLL PCD disable
[3392299.904] FDI TX PLL disable 00000040
[3392299.924] FDI RX PLL disable 00044000
[3392299.944] DPMS off done
[3392300.038] (II) intel(0): Fixed memory allocation layout:
[3392300.038] (II) intel(0): 0x07fff000:            end of stolen memory
[3392300.038] (II) intel(0): 0x07fff000-0x0fffffff: DRI memory manager (131076 kB)
[3392300.038] (II) intel(0): 0x10000000:            end of aperture
[3392300.038] (II) intel(0): BO memory allocation layout:
[3392300.038] (II) intel(0): 0x07fff000:            start of memory manager
[3392300.038] (II) intel(0): 0x08020000-0x0843ffff: front buffer (4224 kB) X tiled
[3392300.038] (II) intel(0): 0x08520000-0x08529fff: HW cursors (40 kB)
[3392300.038] (II) intel(0): 0x10000000:            end of memory manager
[3392300.081] Plane disable
[3392300.081] Pipe disable
[3392300.094] PFIT disable
[3392300.094] FDI TX disable
[3392300.094] FDI RX disable
[3392300.114] FDI TX train 1 preload
[3392300.114] FDI RX train 1 preload
[3392300.134] LVDS port force off
[3392300.134] Transcoder disable
[3392300.154] PCH DPLL disable
[3392300.154] FDI RX PLL PCD disable
[3392300.154] FDI TX PLL disable 001a2040
[3392300.174] FDI RX PLL disable 001c4000
[3392300.194] DPMS off done
[3392300.214] Plane disable
[3392300.214] Pipe disable
[3392300.234] PFIT disable
[3392300.234] FDI TX disable
[3392300.234] FDI RX disable
[3392300.254] FDI TX train 1 preload
[3392300.254] FDI RX train 1 preload
[3392300.274] LVDS port force off
[3392300.274] Transcoder disable
[3392300.294] PCH DPLL disable
[3392300.294] FDI RX PLL PCD disable
[3392300.294] FDI TX PLL disable 00000040
[3392300.314] FDI RX PLL disable 00044000
[3392300.334] DPMS off done
[3392300.355] Plane disable
[3392300.355] Pipe disable
[3392300.374] PFIT disable
[3392300.374] FDI TX disable
[3392300.374] FDI RX disable
[3392300.394] FDI TX train 1 preload
[3392300.394] FDI RX train 1 preload
[3392300.414] LVDS port force off
[3392300.414] Transcoder disable
[3392300.434] PCH DPLL disable
[3392300.434] FDI RX PLL PCD disable
[3392300.434] FDI TX PLL disable 00000040
[3392300.454] FDI RX PLL disable 00044000
[3392300.474] DPMS off done
[3392300.494] (II) intel(0): using SSC reference clock of 120 MHz
[3392300.495] bpp 6
[3392300.514] (II) intel(0): Selecting standard 18 bit TMDS pixel format.
[3392300.675] PCH FDI RX PLL enable
[3392300.714] PCH FDI TX PLL enable 001a2050
[3392300.714] Pipe enable
[3392300.714] Plane enable
[3392300.754] FDI_RX_IIR 0x100
[3392300.754] FDI train 1 done.
[3392300.774] FDI_RX_IIR 0x600
[3392300.774] FDI train 2 done.
[3392300.774] FDI train done
[3392300.794] FDI TX link normal
[3392300.814] transcoder enable
[3392300.814] LUT load
[3392300.815] DPMS on done
[3392300.815] Plane disable
[3392300.815] Pipe disable
[3392300.834] PFIT disable
[3392300.834] FDI TX disable
[3392300.834] FDI RX disable
[3392300.854] FDI TX train 1 preload
[3392300.854] FDI RX train 1 preload
[3392300.874] LVDS port force off
[3392300.874] Transcoder disable
[3392300.894] PCH DPLL disable
[3392300.894] FDI RX PLL PCD disable
[3392300.894] FDI TX PLL disable 001a2040
[3392300.914] FDI RX PLL disable 001c4000
[3392300.934] DPMS off done
[3392300.954] (II) intel(0): Output configuration:
[3392300.954] (II) intel(0):   Pipe A is off
[3392300.954] (II) intel(0):   Display plane A is now disabled and connected to pipe A.
[3392300.954] (II) intel(0):   Pipe B is on
[3392300.954] (II) intel(0):   Display plane B is now enabled and connected to pipe B.
[3392300.955] (II) intel(0):   Output VGA is connected to pipe none
[3392300.955] (II) intel(0):   Output LVDS is connected to pipe B
[3392300.955] (II) intel(0):   Output HDMI-3 is connected to pipe none
[3392300.955] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[3392300.957] (==) intel(0): DPMS enabled
[3392300.957] (==) intel(0): Intel XvMC decoder enabled
[3392300.957] (II) intel(0): Set up textured video
[3392300.995] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[3392300.995] (II) intel(0): direct rendering: DRI2 Enabled
[3392301.006] (--) RandR disabled
[3392301.006] (II) Initializing built-in extension Generic Event Extension
[3392301.006] (II) Initializing built-in extension SHAPE
[3392301.006] (II) Initializing built-in extension MIT-SHM
[3392301.006] (II) Initializing built-in extension XInputExtension
[3392301.006] (II) Initializing built-in extension XTEST
[3392301.006] (II) Initializing built-in extension BIG-REQUESTS
[3392301.006] (II) Initializing built-in extension SYNC
[3392301.006] (II) Initializing built-in extension XKEYBOARD
[3392301.006] (II) Initializing built-in extension XC-MISC
[3392301.006] (II) Initializing built-in extension SECURITY
[3392301.006] (II) Initializing built-in extension XINERAMA
[3392301.006] (II) Initializing built-in extension XFIXES
[3392301.006] (II) Initializing built-in extension RENDER
[3392301.006] (II) Initializing built-in extension RANDR
[3392301.006] (II) Initializing built-in extension COMPOSITE
[3392301.006] (II) Initializing built-in extension DAMAGE
[3392301.113] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[3392301.113] (II) AIGLX: enabled GLX_INTEL_swap_event
[3392301.114] (II) AIGLX: enabled GLX_SGI_make_current_read
[3392301.114] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[3392301.114] (II) AIGLX: Loaded and initialized /usr/X11R6/lib/modules/dri/i965_dri.so
[3392301.114] (II) GLX: Initialized DRI2 GL provider for screen 0
[3392301.115] (II) intel(0): Setting screen physical size to 361 x 203
[3392301.530] (EE) XKB: Couldn't open rules file /usr/X11R6/share/X11/xkb/rules/base
[3392301.530] XKB: Failed to compile keymap
[3392301.530] Keyboard initialization failed. This could be a missing or incorrect setup of xkeyboard-config.
[3392301.530]
Fatal server error:
[3392301.530] Failed to activate core devices.
[3392301.530]
Please consult the The X.Org Foundation support
     at http://wiki.x.org
for help.
[3392301.530] Please also check the log file at "/var/log/Xorg.1.log" for additional information.
[3392301.530]
[3392301.531] (II) AIGLX: Suspending AIGLX clients for VT switch


Помогите, плиз, решить проблему.

Ответить | Правка | Cообщить модератору

Оглавление

Сообщения по теме [Сортировка по времени | RSS]


1. "Xfce4 на OpenBSD не грузится"  +/
Сообщение от pavlinux (ok) on 23-Ноя-12, 03:00 
> Помогите, плиз, решить проблему.

Тут всё написано

[3392301.530] (EE) XKB: Couldn't open rules file /usr/X11R6/share/X11/xkb/rules/base
[3392301.530] XKB: Failed to compile keymap
[3392301.530] Keyboard initialization failed. This could be a missing or incorrect setup of xkeyboard-config.

Ответить | Правка | ^ к родителю #0 | Наверх | Cообщить модератору

2. "Xfce4 на OpenBSD не грузится"  +/
Сообщение от vlalin (ok) on 24-Ноя-12, 18:10 
Почему папка /usr/X11R6/share/X11/xkb/ пуста? На ВМварную машину все поставилось без проблем. Думал, может, драйвер на видеокарту acer'a... Но вроде дрова стоят...


>> Помогите, плиз, решить проблему.
> Тут всё написано
> [3392301.530] (EE) XKB: Couldn't open rules file /usr/X11R6/share/X11/xkb/rules/base
> [3392301.530] XKB: Failed to compile keymap
> [3392301.530] Keyboard initialization failed. This could be a missing or incorrect setup
> of xkeyboard-config.

Ответить | Правка | ^ к родителю #1 | Наверх | Cообщить модератору

3. "Xfce4 на OpenBSD не грузится"  +/
Сообщение от pavlinux (ok) on 26-Ноя-12, 16:38 
> Почему папка /usr/X11R6/share/X11/xkb/ пуста?

скорее всего xkb не установился.

Ответить | Правка | ^ к родителю #2 | Наверх | Cообщить модератору

4. "Xfce4 на OpenBSD не грузится"  +/
Сообщение от vlalin (ok) on 05-Дек-12, 10:47 
>> Почему папка /usr/X11R6/share/X11/xkb/ пуста?
> скорее всего xkb не установился.

Как установить xkb? пакет xkbset? он скачан...

Ответить | Правка | ^ к родителю #3 | Наверх | Cообщить модератору

5. "Xfce4 на OpenBSD не грузится"  +/
Сообщение от vlalin (ok) on 06-Дек-12, 14:05 
>>> Почему папка /usr/X11R6/share/X11/xkb/ пуста?
>> скорее всего xkb не установился.
> Как установить xkb? пакет xkbset? он скачан...

Косяк найден - при установке сетов забыл один немаловажный компонент - xshare51

После его установки xfce заработал.

Ответить | Правка | ^ к родителю #4 | Наверх | Cообщить модератору

6. "Xfce4 на OpenBSD не грузится"  +/
Сообщение от VolanD (ok) on 24-Дек-12, 12:39 
>>>> Почему папка /usr/X11R6/share/X11/xkb/ пуста?
>>> скорее всего xkb не установился.
>> Как установить xkb? пакет xkbset? он скачан...
> Косяк найден - при установке сетов забыл один немаловажный компонент - xshare51
> После его установки xfce заработал.

Да поставили бы xubuntu и все заработало бы сразу )))

Ответить | Правка | ^ к родителю #5 | Наверх | Cообщить модератору

Архив | Удалить

Рекомендовать для помещения в FAQ | Индекс форумов | Темы | Пред. тема | След. тема




Партнёры:
PostgresPro
Inferno Solutions
Hosting by Hoster.ru
Хостинг:

Закладки на сайте
Проследить за страницей
Created 1996-2025 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру