Доброго времени суток!
Есть: 2621XM (ниже sh ver)
Не могу пробросить IPSec через NAT внутрь.
По докам с cisco.com версия 12.2
этого не умеет, рекомендовали обновить на более новую.
Следуя инструкциям залил во flash образ с ftp (copy ftp: flash:),
далее действовал инструкции с cisco.com
Conf t -> no boot system -> boot system flash: c2600-\\\\\\
Далее ^Z -> write memory -> reloadПосле reload на этапе загрузки ошибка:
=========================================
program load complete, entry point: 0x80008000, size: 0x66ae10
Self decompressing the image : ###########################
##[OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
00036D 0X00103980 C2621XM Dual Fast Ethernet
0X000F3BB0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00408530
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 5Mb.
Using 15 percent iomem. [5Mb/32Mb]
Далее идет
%IPNAT-6-NAT_CREATED: Created ? тххххххххххххххххххххххххххххххх (много правил по НАТу)
и появляется следующее:
=========================================
%IPNAT-6-NAT_CREATED: Created ? //////////////////////////////////////////
%SYS-6-READ_BOOTFILE_FAIL: flash:c2600-io3-mz.123-19.bin File read failed -- Unknown error 0.
%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.
boot of "c2600-io3-mz.123-19.bin" using boot helper
"flash:c2600-io3-mz.122-13.T4.bin" failed
error returned: File read failed -- Unknown error 0
loadprog: error - on file open
boot: cannot load "c2600-io3-mz.123-19.bin"
=========================================
Такое впечатление, что криво залил образ во flash
После ошибки идет reload и происходит загрузка старого образа 12.2
Уже второй день ничего не получается. Прошу доброго совета.
С уважением, Андрей, aka Pep.
================== show version =====================================
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 32768 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x66ae10
Self decompressing the image : ### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
00036D 0X00103980 C2621XM Dual Fast Ethernet
0X000F3BB0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00408530
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 5Mb.
Using 15 percent iomem. [5Mb/32Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IO3-M), Version 12.2(13)T4, RELEASE SOFTWARE (fc2)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 01-May-03 11:08 by eaarmas
Image text-base: 0x80008098, data-base: 0x80BB8080
cisco 2621XM (MPC860P) processor (revision 0x100) with 27648K/5120K bytes of memory.
Processor board ID JAD07120KXT (430966554)
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)