Приветствую всех. У меня такой вопрос. Имеется Cisco 805. Настраиваю Cisco и сохраняю конфигурацию в NVRAM. Выдается сообщение:
Rout#write
Building configuration...
-> WARNING: no valid "boot system" command. TinyROM will
-> pick an IOS image to boot.
[OK]
Rout#
Идентичная команда:
Rout#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
-> WARNING: no valid "boot system" command. TinyROM will
-> pick an IOS image to boot.
[OK]
Rout#
Вроде все сохраняет, но почему выскакивает это сообщение?
Решил перенастроить машку:
Rout#erase startup-config
Erasing the nvram filesystem will remove all files! Continue? [confirm]
-> WARNING: no valid "boot system" command. TinyROM will
-> pick an IOS image to boot.
[OK]
Erase of nvram: complete
Rout#
Перегружаюсь и вижу следующее:
Rout#reload
Proceed with reload? [confirm]
-> WARNING: no valid "boot system" command. TinyROM will
-> pick an IOS image to boot.
-> WARNING: no valid "boot system" command. TinyROM will
-> pick an IOS image to boot.
00:05:42: %SYS-5-RELOAD: Reload requested
TinyROM version 1.4(1)
19:37 11/07/00
Copyright (c) 1998-2000 by cisco Systems, Inc.
All rights reserved.
POST ............ OK. 8MB DRAM, 8MB Flash.
-> Configured boot failed, attempting fallback boot.
Booting "c805-y6-mw.122-8.T10.bin" ...,
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C805 Software (C805-Y6-MW), Version 12.2(8)T10, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 29-May-03 21:49 by kellythw
Image text-base: 0x00180000, data-base: 0x007BA000
Cisco C805 (MPC850) processor (revision 0) with 48128K bytes of virtual memory.
Processor board ID FOC072606EB (1220454479)
CPU part number 0x2101
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 Serial(sync/async) network interface(s)
8M bytes of physical memory (DRAM)
8K bytes of non-volatile configuration memory
8M bytes of flash on board (4M from flash card)
-> %Error opening tftp://10.1.2.25/network-confg (Timed out)
SETUP: new interface Serial0 placed in "shutdown" state
Press RETURN to get started!
00:00:23: %LINK-3-UPDOWN: Interface Serial0, changed state to down
00:00:23: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
00:00:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up
00:00:32: AUTOINSTALL: Ethernet0 is assigned 10.0.0.14
00:00:32: AUTOINSTALL: Obtain siaddr 10.1.2.25 (as config server)
00:01:17: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C805 Software (C805-Y6-MW), Version 12.2(8)T10, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 29-May-03 21:49 by kellythw
00:01:17: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
00:01:17: %LINK-5-CHANGED: Interface Serial0, changed state to administratively down
00:01:18: %IP-5-WEBINST_KILL: Terminating DNS process
Router>
-> %Error opening tftp://10.1.2.25/cisconet.cfg (Timed out)
-> %Error opening tftp://10.1.2.25/router-confg (Timed out)
Что за tftp-сервер, к которому он обращается?
Заранее спасибо.
Вариант для распечатки
Маршрутизаторы CISCO и др. оборудование. (Public)
(??) on
02-Апр-04, 16:03 (MSK)
