forum.opennet.ru - "Duplicated IP во время конфигурации влан 1" (3)

форумы

помощь

поиск

регистрация

майллист

ВХОД

слежка

"Duplicated IP во время конфигурации влан 1"

Форумы Маршрутизаторы CISCO и др. оборудование. (Public)
Вариант для распечатки		Архивированная нить - только для чтения! Пред. тема \| След. тема
Изначальное сообщение		[Проследить за развитием треда]

"Duplicated IP во время конфигурации влан 1"
Сообщение от cska (ok) on 15-Апр-04, 20:26 (MSK)
Речь идет о Cisco 6503. Сконфигурил только порт 48 в влан 1 для менежмента. Дал ему IP. Подсоединяюсь телнет , на консоль выскыкивает ошибка "Duplicated IP was sent from MAC xxx". После этого по телнет можно подсоединится только к Layer3, а не к Layer2. Причем иногда его таки прорывает (может после того как потереть arp ) и по телнет можно подсоединится к Layer2 , но не надолго. На cisco.com ничего об этом не нашел. Может кто знает что за баранина. Спасибо за помощь.
	Рекомендовать в FAQ \| Cообщить модератору \| Наверх

Оглавление

Duplicated IP во время конфигурации влан 1, ВОЛКА, 20:50 , 15-Апр-04, (1)
- Duplicated IP во время конфигурации влан 1, cska, 22:27 , 15-Апр-04, (2)
  - Duplicated IP во время конфигурации влан 1, cska, 17:03 , 20-Апр-04, (3)

Индекс форумов | Темы | Пред. тема | След. тема

Сообщения по теме

1. "Duplicated IP во время конфигурации влан 1"

Сообщение от ВОЛКА on 15-Апр-04, 20:50  (MSK)

покажите конфиг catOS'а и msfc

Рекомендовать в FAQ | Cообщить модератору | Наверх

2. "Duplicated IP во время конфигурации влан 1"

Сообщение от cska (ok) on 15-Апр-04, 22:27  (MSK)

>покажите конфиг catOS'а и msfc
CAT OSConsole> (enable) show running-config
This command shows non-default configurations only.
Use 'show config all' to show both default and non-default configurations.
.................
..........................
.............................
........................
..
begin
!
# ***** NON-DEFAULT CONFIGURATION *****
!
!
#time: Thu Apr 15 2004, 11:07:21
!
#version 7.6(5)
!
set password $2$jm.V$VYWvdP8I8WZVxTEnTZIvF0
set enablepass $2$9c7X$cUzyszb/CRWGxH33r7ZF./
!
#!
#mac address reduction
set spantree macreduction disable
!
#vtp
set vtp domain Cisco_Catalist
set vlan 1 name default type ethernet mtu 1500 said 100001 state active
set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee
set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm
set vlan 2,21,101,105,109-110,113-117,120-121,123,129-130,133,147-148,200
set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf
!
#dot1q-all-tagged
set dot1q-all-tagged enable
!
#Layer 2 protocol tunnel
set l2protocol-tunnel trunk enable
!
#ip
set interface sc0 1 10.12.240.205/255.255.255.0 10.12.240.255
set interface sc1 0 0.0.0.0/0.0.0.0 0.0.0.0
set interface sc1 down
set ip route 0.0.0.0/0.0.0.0         10.12.240.1
set ip alias default         0.0.0.0
!
#set boot command
set boot config-register 0x2
set boot system flash bootflash:cat6000-sup2k8.7-6-5.bin
set boot system flash bootflash:cat6000-sup2k8.7-6-5.1
!
#LACP channel
set lacp-channel system-priority 2000
!
#channelprotocol
set channelprotocol lacp 2
!
#port channel
set port lacp-channel 2/17-20 123
set port lacp-channel 2/2-4 133
set port lacp-channel 2/5-8 134
set port lacp-channel 2/1 138
!
# default port status is enable
!
!
#module 1 : 2-port 1000BaseX Supervisor
set vlan 2    1/2
set vlan 117  1/1
!
#module 2 : 48-port 10/100/1000BaseT Ethernet
set vlan 2    2/12,2/22,2/24-28,2/30-32,2/35-46
set vlan 101  2/1-4,2/9-11
set vlan 105  2/5-8
set vlan 113  2/13
set vlan 114  2/14
set vlan 115  2/15
set vlan 116  2/16
set vlan 117  2/17-20,2/34
set vlan 121  2/21
set vlan 123  2/23
set vlan 129  2/29
set vlan 133  2/33
set vlan 147  2/47
set port speed      2/1-8,2/17-19  100
set port duplex     2/1-8,2/17-19  full
set trunk 2/15 on dot1q 1-1005,1025-4094
set trunk 2/20 off dot1q 1-1005,1025-4094
clear trunk 2/21 1001-1005,1025-4094
set trunk 2/21 off dot1q 1-1000
set trunk 2/30 on dot1q 1-1005,1025-4094
set trunk 2/31 off dot1q 1-1005,1025-4094
set port dot1qtunnel 2/31 access
set port lacp-channel 2/1-4 mode on
set port lacp-channel 2/17-18 mode off
set port lacp-channel 2/1 port-priority 10
set port lacp-channel 2/2 port-priority 10
set port lacp-channel 2/3 port-priority 10
set port lacp-channel 2/4 port-priority 10
set port lacp-channel 2/5 port-priority 10
set port lacp-channel 2/6 port-priority 10
set port lacp-channel 2/7 port-priority 10
set port lacp-channel 2/8 port-priority 10
!
#module 3 empty
!
#module 15 : 1-port Multilayer Switch Feature Card
set vlan 200  15/1
!
#module 16 empty
end

IOS
Cisco48#show running-config
Building configuration...
Current configuration : 3028 bytes
!
version 12.1
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Cisco48
!
boot system bootflash:c6msfc2-psv-mz.121-13.E9.bin
boot system flash cat6000-sup2k8.7-6-5.bin
boot bootldr bootflash:c6msfc2-boot-mz.121-13.E9.bin
enable password qa
!
username smart password 0 smart
clock timezone PDT -7
ip subnet-zero
!
!
!
!
key chain abc
key 1
  key-string xyz
key 2
  key-string xxx
key 12
  key-string xxx
key chain ofer
key 1
  key-string abcd
key chain acb
key 1
  key-string xyz
key chain vl
key 1
  key-string xxx
key chain vlan
key 2
  key-string xxx
key 20
  key-string aaaa
key chain 1111
key 20
  key-string aaaa
key chain vln
key 1
  key-string xyz
!
!
!
interface Tunnel21
no ip address
!
interface Vlan1
ip address 10.12.240.205 255.255.255.0
!
interface Vlan2
ip address 2.2.2.2 255.255.255.0
!
interface Vlan101
no ip address
!
interface Vlan102
no ip address
shutdown
!
interface Vlan105
ip address 5.5.5.5 255.255.255.0
ip rip send version 2
ip rip receive version 2
!
interface Vlan109
ip address 9.9.9.9 255.255.255.0
!
interface Vlan110
ip address 48.48.48.48 255.255.255.0
!
interface Vlan113
ip address 13.13.13.13 255.255.255.0
!
interface Vlan114
ip address 14.14.14.14 255.255.255.0
no ip redirects
no ip unreachables
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 xxx
!
interface Vlan115
ip address 15.15.15.15 255.0.0.0
ip rip send version 2
ip rip receive version 2
!
interface Vlan116
ip address 16.16.16.16 255.255.255.0
!
interface Vlan117
ip address 17.17.17.17 255.255.255.0
!
interface Vlan120
no ip address
!
interface Vlan121
ip address 21.21.21.21 255.255.255.0
ip rip send version 1
ip rip receive version 1
!
interface Vlan121.21
!
interface Vlan129
ip address 29.29.29.29 255.255.255.0
ip rip send version 1 2
ip rip receive version 1 2
!
interface Vlan130
ip address 30.30.30.30 255.255.255.0
!
interface Vlan133
ip address 33.33.33.33 255.255.255.0
!
interface Vlan147
ip address 97.97.97.25 255.255.255.0
!
interface Vlan1143
no ip address
shutdown
!
interface Vlan1213
no ip address
shutdown
!
router ospf 117
router-id 205.0.0.117
log-adjacency-changes
redistribute ospf 133 subnets
network 17.17.17.0 0.0.0.255 area 117
!
router ospf 133
log-adjacency-changes
network 33.33.33.0 0.0.0.255 area 133
!
router ospf 113
router-id 205.0.0.113
log-adjacency-changes
!
router rip
redistribute connected
redistribute static
network 1.0.0.0
network 5.0.0.0
network 15.0.0.0
network 18.0.0.0
network 21.0.0.0
network 29.0.0.0
network 32.0.0.0
network 97.0.0.0
neighbor 29.29.29.1
default-metric 4
!
ip classless
ip route 36.29.29.0 255.255.255.0 29.29.29.31 8
ip route 169.0.0.0 255.0.0.0 14.14.14.66
ip http server
!
!
!
!
line con 0
exec-timeout 0 0
password smart
login local
line vty 0 4
privilege level 0
password smart
login local
line vty 5
privilege level 0
password smart
login local
line vty 6 15
password smart
login local
!
end

Рекомендовать в FAQ | Cообщить модератору | Наверх

3. "Duplicated IP во время конфигурации влан 1"

Сообщение от cska (ok) on 20-Апр-04, 17:03  (MSK)

>>покажите конфиг catOS'а и msfc
>
>CAT OSConsole> (enable) show running-config
>This command shows non-default configurations only.
>Use 'show config all' to show both default and non-default configurations.
>.................
>..........................
>.............................
>
>........................
>
>..
>
>begin
>!
># ***** NON-DEFAULT CONFIGURATION *****
>!
>!
>#time: Thu Apr 15 2004, 11:07:21
>!
>#version 7.6(5)
>!
>set password $2$jm.V$VYWvdP8I8WZVxTEnTZIvF0
>set enablepass $2$9c7X$cUzyszb/CRWGxH33r7ZF./
>
>!
>#!
>#mac address reduction
>set spantree macreduction disable
>!
>#vtp
>set vtp domain Cisco_Catalist
>set vlan 1 name default type ethernet mtu 1500 said 100001 state
>active
>set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state
>active
>set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state
>active stp ieee
>set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state
>active stp ibm
>set vlan 2,21,101,105,109-110,113-117,120-121,123,129-130,133,147-148,200
>set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state
>active mode srb aremaxhop 7 stemaxhop 7 backupcrf
>!
>#dot1q-all-tagged
>set dot1q-all-tagged enable
>!
>#Layer 2 protocol tunnel
>set l2protocol-tunnel trunk enable
>!
>#ip
>set interface sc0 1 10.12.240.205/255.255.255.0 10.12.240.255
>
>set interface sc1 0 0.0.0.0/0.0.0.0 0.0.0.0
>
>set interface sc1 down
>set ip route 0.0.0.0/0.0.0.0
>10.12.240.1
>set ip alias default
>0.0.0.0
>!
>#set boot command
>set boot config-register 0x2
>set boot system flash bootflash:cat6000-sup2k8.7-6-5.bin
>set boot system flash bootflash:cat6000-sup2k8.7-6-5.1
>!
>#LACP channel
>set lacp-channel system-priority 2000
>!
>#channelprotocol
>set channelprotocol lacp 2
>!
>#port channel
>set port lacp-channel 2/17-20 123
>set port lacp-channel 2/2-4 133
>set port lacp-channel 2/5-8 134
>set port lacp-channel 2/1 138
>!
># default port status is enable
>!
>!
>#module 1 : 2-port 1000BaseX Supervisor
>set vlan 2    1/2
>set vlan 117  1/1
>!
>#module 2 : 48-port 10/100/1000BaseT Ethernet
>set vlan 2    2/12,2/22,2/24-28,2/30-32,2/35-46
>set vlan 101  2/1-4,2/9-11
>set vlan 105  2/5-8
>set vlan 113  2/13
>set vlan 114  2/14
>set vlan 115  2/15
>set vlan 116  2/16
>set vlan 117  2/17-20,2/34
>set vlan 121  2/21
>set vlan 123  2/23
>set vlan 129  2/29
>set vlan 133  2/33
>set vlan 147  2/47
>set port speed      2/1-8,2/17-19  100
>set port duplex     2/1-8,2/17-19  full
>set trunk 2/15 on dot1q 1-1005,1025-4094
>set trunk 2/20 off dot1q 1-1005,1025-4094
>clear trunk 2/21 1001-1005,1025-4094
>set trunk 2/21 off dot1q 1-1000
>set trunk 2/30 on dot1q 1-1005,1025-4094
>set trunk 2/31 off dot1q 1-1005,1025-4094
>set port dot1qtunnel 2/31 access
>set port lacp-channel 2/1-4 mode on
>set port lacp-channel 2/17-18 mode off
>set port lacp-channel 2/1 port-priority 10
>set port lacp-channel 2/2 port-priority 10
>set port lacp-channel 2/3 port-priority 10
>set port lacp-channel 2/4 port-priority 10
>set port lacp-channel 2/5 port-priority 10
>set port lacp-channel 2/6 port-priority 10
>set port lacp-channel 2/7 port-priority 10
>set port lacp-channel 2/8 port-priority 10
>!
>#module 3 empty
>!
>#module 15 : 1-port Multilayer Switch Feature Card
>set vlan 200  15/1
>!
>#module 16 empty
>end
>
>
>
>IOS
>
>Cisco48#show running-config
>Building configuration...
>
>Current configuration : 3028 bytes
>!
>version 12.1
>service timestamps debug uptime
>service timestamps log uptime
>no service password-encryption
>!
>hostname Cisco48
>!
>boot system bootflash:c6msfc2-psv-mz.121-13.E9.bin
>boot system flash cat6000-sup2k8.7-6-5.bin
>boot bootldr bootflash:c6msfc2-boot-mz.121-13.E9.bin
>enable password qa
>!
>username smart password 0 smart
>clock timezone PDT -7
>ip subnet-zero
>!
>!
>!
>!
>key chain abc
> key 1
>  key-string xyz
> key 2
>  key-string xxx
> key 12
>  key-string xxx
>key chain ofer
> key 1
>  key-string abcd
>key chain acb
> key 1
>  key-string xyz
>key chain vl
> key 1
>  key-string xxx
>key chain vlan
> key 2
>  key-string xxx
> key 20
>  key-string aaaa
>key chain 1111
> key 20
>  key-string aaaa
>key chain vln
> key 1
>  key-string xyz
>!
>!
>!
>interface Tunnel21
> no ip address
>!
>interface Vlan1
> ip address 10.12.240.205 255.255.255.0
>!
>interface Vlan2
> ip address 2.2.2.2 255.255.255.0
>!
>interface Vlan101
> no ip address
>!
>interface Vlan102
> no ip address
> shutdown
>!
>interface Vlan105
> ip address 5.5.5.5 255.255.255.0
> ip rip send version 2
> ip rip receive version 2
>!
>interface Vlan109
> ip address 9.9.9.9 255.255.255.0
>!
>interface Vlan110
> ip address 48.48.48.48 255.255.255.0
>!
>interface Vlan113
> ip address 13.13.13.13 255.255.255.0
>!
>interface Vlan114
> ip address 14.14.14.14 255.255.255.0
> no ip redirects
> no ip unreachables
> ip ospf authentication message-digest
> ip ospf message-digest-key 1 md5 xxx
>!
>interface Vlan115
> ip address 15.15.15.15 255.0.0.0
> ip rip send version 2
> ip rip receive version 2
>!
>interface Vlan116
> ip address 16.16.16.16 255.255.255.0
>!
>interface Vlan117
> ip address 17.17.17.17 255.255.255.0
>!
>interface Vlan120
> no ip address
>!
>interface Vlan121
> ip address 21.21.21.21 255.255.255.0
> ip rip send version 1
> ip rip receive version 1
>!
>interface Vlan121.21
>!
>interface Vlan129
> ip address 29.29.29.29 255.255.255.0
> ip rip send version 1 2
> ip rip receive version 1 2
>!
>interface Vlan130
> ip address 30.30.30.30 255.255.255.0
>!
>interface Vlan133
> ip address 33.33.33.33 255.255.255.0
>!
>interface Vlan147
> ip address 97.97.97.25 255.255.255.0
>!
>interface Vlan1143
> no ip address
> shutdown
>!
>interface Vlan1213
> no ip address
> shutdown
>!
>router ospf 117
> router-id 205.0.0.117
> log-adjacency-changes
> redistribute ospf 133 subnets
> network 17.17.17.0 0.0.0.255 area 117
>!
>router ospf 133
> log-adjacency-changes
> network 33.33.33.0 0.0.0.255 area 133
>!
>router ospf 113
> router-id 205.0.0.113
> log-adjacency-changes
>!
>router rip
> redistribute connected
> redistribute static
> network 1.0.0.0
> network 5.0.0.0
> network 15.0.0.0
> network 18.0.0.0
> network 21.0.0.0
> network 29.0.0.0
> network 32.0.0.0
> network 97.0.0.0
> neighbor 29.29.29.1
> default-metric 4
>!
>ip classless
>ip route 36.29.29.0 255.255.255.0 29.29.29.31 8
>ip route 169.0.0.0 255.0.0.0 14.14.14.66
>ip http server
>!
>!
>!
>!
>line con 0
> exec-timeout 0 0
> password smart
> login local
>line vty 0 4
> privilege level 0
> password smart
> login local
>line vty 5
> privilege level 0
> password smart
> login local
>line vty 6 15
> password smart
> login local
>!
>end

Если кому еще интересно, таки сам допер.
В CatOS и IOS можно сконфигурировать IP.
В CatOS на весь коммутатор а в IOS на порт.
В CatOS
set interface sc0 1(влан) 10.12.240.205/255.255.255.0 10.12.240.255
В IOS
interface Vlan1
> ip address 10.12.240.205 255.255.255.0

Мас адреса там разные (хотя в коммутаторе на всех портах один мас).
Отсюда и проблема. Всем удачи.

Рекомендовать в FAQ | Cообщить модератору | Наверх

Удалить

Индекс форумов | Темы | Пред. тема | След. тема

Пожалуйста, прежде чем написать сообщение, ознакомьтесь с данными рекомендациями.

Партнёры:

Хостинг:

Закладки на сайте
Проследить за страницей

Created 1996-2024 by Maxim Chirkov
Добавить, Поддержать, Вебмастеру

1. "Duplicated IP во время конфигурации влан 1"
Сообщение от ВОЛКА on 15-Апр-04, 20:50 (MSK)
покажите конфиг catOS'а и msfc
	Рекомендовать в FAQ \| Cообщить модератору \| Наверх


	2. "Duplicated IP во время конфигурации влан 1"
	Сообщение от cska (ok) on 15-Апр-04, 22:27 (MSK)
	>покажите конфиг catOS'а и msfc CAT OSConsole> (enable) show running-config This command shows non-default configurations only. Use 'show config all' to show both default and non-default configurations. ................. .......................... ............................. ........................ .. begin ! # *** NON-DEFAULT CONFIGURATION *** ! ! #time: Thu Apr 15 2004, 11:07:21 ! #version 7.6(5) ! set password $2$jm.V$VYWvdP8I8WZVxTEnTZIvF0 set enablepass $2$9c7X$cUzyszb/CRWGxH33r7ZF./ ! #! #mac address reduction set spantree macreduction disable ! #vtp set vtp domain Cisco_Catalist set vlan 1 name default type ethernet mtu 1500 said 100001 state active set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm set vlan 2,21,101,105,109-110,113-117,120-121,123,129-130,133,147-148,200 set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf ! #dot1q-all-tagged set dot1q-all-tagged enable ! #Layer 2 protocol tunnel set l2protocol-tunnel trunk enable ! #ip set interface sc0 1 10.12.240.205/255.255.255.0 10.12.240.255 set interface sc1 0 0.0.0.0/0.0.0.0 0.0.0.0 set interface sc1 down set ip route 0.0.0.0/0.0.0.0 10.12.240.1 set ip alias default 0.0.0.0 ! #set boot command set boot config-register 0x2 set boot system flash bootflash:cat6000-sup2k8.7-6-5.bin set boot system flash bootflash:cat6000-sup2k8.7-6-5.1 ! #LACP channel set lacp-channel system-priority 2000 ! #channelprotocol set channelprotocol lacp 2 ! #port channel set port lacp-channel 2/17-20 123 set port lacp-channel 2/2-4 133 set port lacp-channel 2/5-8 134 set port lacp-channel 2/1 138 ! # default port status is enable ! ! #module 1 : 2-port 1000BaseX Supervisor set vlan 2 1/2 set vlan 117 1/1 ! #module 2 : 48-port 10/100/1000BaseT Ethernet set vlan 2 2/12,2/22,2/24-28,2/30-32,2/35-46 set vlan 101 2/1-4,2/9-11 set vlan 105 2/5-8 set vlan 113 2/13 set vlan 114 2/14 set vlan 115 2/15 set vlan 116 2/16 set vlan 117 2/17-20,2/34 set vlan 121 2/21 set vlan 123 2/23 set vlan 129 2/29 set vlan 133 2/33 set vlan 147 2/47 set port speed 2/1-8,2/17-19 100 set port duplex 2/1-8,2/17-19 full set trunk 2/15 on dot1q 1-1005,1025-4094 set trunk 2/20 off dot1q 1-1005,1025-4094 clear trunk 2/21 1001-1005,1025-4094 set trunk 2/21 off dot1q 1-1000 set trunk 2/30 on dot1q 1-1005,1025-4094 set trunk 2/31 off dot1q 1-1005,1025-4094 set port dot1qtunnel 2/31 access set port lacp-channel 2/1-4 mode on set port lacp-channel 2/17-18 mode off set port lacp-channel 2/1 port-priority 10 set port lacp-channel 2/2 port-priority 10 set port lacp-channel 2/3 port-priority 10 set port lacp-channel 2/4 port-priority 10 set port lacp-channel 2/5 port-priority 10 set port lacp-channel 2/6 port-priority 10 set port lacp-channel 2/7 port-priority 10 set port lacp-channel 2/8 port-priority 10 ! #module 3 empty ! #module 15 : 1-port Multilayer Switch Feature Card set vlan 200 15/1 ! #module 16 empty end IOS Cisco48#show running-config Building configuration... Current configuration : 3028 bytes ! version 12.1 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname Cisco48 ! boot system bootflash:c6msfc2-psv-mz.121-13.E9.bin boot system flash cat6000-sup2k8.7-6-5.bin boot bootldr bootflash:c6msfc2-boot-mz.121-13.E9.bin enable password qa ! username smart password 0 smart clock timezone PDT -7 ip subnet-zero ! ! ! ! key chain abc key 1 key-string xyz key 2 key-string xxx key 12 key-string xxx key chain ofer key 1 key-string abcd key chain acb key 1 key-string xyz key chain vl key 1 key-string xxx key chain vlan key 2 key-string xxx key 20 key-string aaaa key chain 1111 key 20 key-string aaaa key chain vln key 1 key-string xyz ! ! ! interface Tunnel21 no ip address ! interface Vlan1 ip address 10.12.240.205 255.255.255.0 ! interface Vlan2 ip address 2.2.2.2 255.255.255.0 ! interface Vlan101 no ip address ! interface Vlan102 no ip address shutdown ! interface Vlan105 ip address 5.5.5.5 255.255.255.0 ip rip send version 2 ip rip receive version 2 ! interface Vlan109 ip address 9.9.9.9 255.255.255.0 ! interface Vlan110 ip address 48.48.48.48 255.255.255.0 ! interface Vlan113 ip address 13.13.13.13 255.255.255.0 ! interface Vlan114 ip address 14.14.14.14 255.255.255.0 no ip redirects no ip unreachables ip ospf authentication message-digest ip ospf message-digest-key 1 md5 xxx ! interface Vlan115 ip address 15.15.15.15 255.0.0.0 ip rip send version 2 ip rip receive version 2 ! interface Vlan116 ip address 16.16.16.16 255.255.255.0 ! interface Vlan117 ip address 17.17.17.17 255.255.255.0 ! interface Vlan120 no ip address ! interface Vlan121 ip address 21.21.21.21 255.255.255.0 ip rip send version 1 ip rip receive version 1 ! interface Vlan121.21 ! interface Vlan129 ip address 29.29.29.29 255.255.255.0 ip rip send version 1 2 ip rip receive version 1 2 ! interface Vlan130 ip address 30.30.30.30 255.255.255.0 ! interface Vlan133 ip address 33.33.33.33 255.255.255.0 ! interface Vlan147 ip address 97.97.97.25 255.255.255.0 ! interface Vlan1143 no ip address shutdown ! interface Vlan1213 no ip address shutdown ! router ospf 117 router-id 205.0.0.117 log-adjacency-changes redistribute ospf 133 subnets network 17.17.17.0 0.0.0.255 area 117 ! router ospf 133 log-adjacency-changes network 33.33.33.0 0.0.0.255 area 133 ! router ospf 113 router-id 205.0.0.113 log-adjacency-changes ! router rip redistribute connected redistribute static network 1.0.0.0 network 5.0.0.0 network 15.0.0.0 network 18.0.0.0 network 21.0.0.0 network 29.0.0.0 network 32.0.0.0 network 97.0.0.0 neighbor 29.29.29.1 default-metric 4 ! ip classless ip route 36.29.29.0 255.255.255.0 29.29.29.31 8 ip route 169.0.0.0 255.0.0.0 14.14.14.66 ip http server ! ! ! ! line con 0 exec-timeout 0 0 password smart login local line vty 0 4 privilege level 0 password smart login local line vty 5 privilege level 0 password smart login local line vty 6 15 password smart login local ! end
		Рекомендовать в FAQ \| Cообщить модератору \| Наверх


	3. "Duplicated IP во время конфигурации влан 1"
	Сообщение от cska (ok) on 20-Апр-04, 17:03 (MSK)
	>>покажите конфиг catOS'а и msfc > >CAT OSConsole> (enable) show running-config >This command shows non-default configurations only. >Use 'show config all' to show both default and non-default configurations. >................. >.......................... >............................. > >........................ > >.. > >begin >! ># *** NON-DEFAULT CONFIGURATION *** >! >! >#time: Thu Apr 15 2004, 11:07:21 >! >#version 7.6(5) >! >set password $2$jm.V$VYWvdP8I8WZVxTEnTZIvF0 >set enablepass $2$9c7X$cUzyszb/CRWGxH33r7ZF./ > >! >#! >#mac address reduction >set spantree macreduction disable >! >#vtp >set vtp domain Cisco_Catalist >set vlan 1 name default type ethernet mtu 1500 said 100001 state >active >set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state >active >set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state >active stp ieee >set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state >active stp ibm >set vlan 2,21,101,105,109-110,113-117,120-121,123,129-130,133,147-148,200 >set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state >active mode srb aremaxhop 7 stemaxhop 7 backupcrf >! >#dot1q-all-tagged >set dot1q-all-tagged enable >! >#Layer 2 protocol tunnel >set l2protocol-tunnel trunk enable >! >#ip >set interface sc0 1 10.12.240.205/255.255.255.0 10.12.240.255 > >set interface sc1 0 0.0.0.0/0.0.0.0 0.0.0.0 > >set interface sc1 down >set ip route 0.0.0.0/0.0.0.0 >10.12.240.1 >set ip alias default >0.0.0.0 >! >#set boot command >set boot config-register 0x2 >set boot system flash bootflash:cat6000-sup2k8.7-6-5.bin >set boot system flash bootflash:cat6000-sup2k8.7-6-5.1 >! >#LACP channel >set lacp-channel system-priority 2000 >! >#channelprotocol >set channelprotocol lacp 2 >! >#port channel >set port lacp-channel 2/17-20 123 >set port lacp-channel 2/2-4 133 >set port lacp-channel 2/5-8 134 >set port lacp-channel 2/1 138 >! ># default port status is enable >! >! >#module 1 : 2-port 1000BaseX Supervisor >set vlan 2 1/2 >set vlan 117 1/1 >! >#module 2 : 48-port 10/100/1000BaseT Ethernet >set vlan 2 2/12,2/22,2/24-28,2/30-32,2/35-46 >set vlan 101 2/1-4,2/9-11 >set vlan 105 2/5-8 >set vlan 113 2/13 >set vlan 114 2/14 >set vlan 115 2/15 >set vlan 116 2/16 >set vlan 117 2/17-20,2/34 >set vlan 121 2/21 >set vlan 123 2/23 >set vlan 129 2/29 >set vlan 133 2/33 >set vlan 147 2/47 >set port speed 2/1-8,2/17-19 100 >set port duplex 2/1-8,2/17-19 full >set trunk 2/15 on dot1q 1-1005,1025-4094 >set trunk 2/20 off dot1q 1-1005,1025-4094 >clear trunk 2/21 1001-1005,1025-4094 >set trunk 2/21 off dot1q 1-1000 >set trunk 2/30 on dot1q 1-1005,1025-4094 >set trunk 2/31 off dot1q 1-1005,1025-4094 >set port dot1qtunnel 2/31 access >set port lacp-channel 2/1-4 mode on >set port lacp-channel 2/17-18 mode off >set port lacp-channel 2/1 port-priority 10 >set port lacp-channel 2/2 port-priority 10 >set port lacp-channel 2/3 port-priority 10 >set port lacp-channel 2/4 port-priority 10 >set port lacp-channel 2/5 port-priority 10 >set port lacp-channel 2/6 port-priority 10 >set port lacp-channel 2/7 port-priority 10 >set port lacp-channel 2/8 port-priority 10 >! >#module 3 empty >! >#module 15 : 1-port Multilayer Switch Feature Card >set vlan 200 15/1 >! >#module 16 empty >end > > > >IOS > >Cisco48#show running-config >Building configuration... > >Current configuration : 3028 bytes >! >version 12.1 >service timestamps debug uptime >service timestamps log uptime >no service password-encryption >! >hostname Cisco48 >! >boot system bootflash:c6msfc2-psv-mz.121-13.E9.bin >boot system flash cat6000-sup2k8.7-6-5.bin >boot bootldr bootflash:c6msfc2-boot-mz.121-13.E9.bin >enable password qa >! >username smart password 0 smart >clock timezone PDT -7 >ip subnet-zero >! >! >! >! >key chain abc > key 1 > key-string xyz > key 2 > key-string xxx > key 12 > key-string xxx >key chain ofer > key 1 > key-string abcd >key chain acb > key 1 > key-string xyz >key chain vl > key 1 > key-string xxx >key chain vlan > key 2 > key-string xxx > key 20 > key-string aaaa >key chain 1111 > key 20 > key-string aaaa >key chain vln > key 1 > key-string xyz >! >! >! >interface Tunnel21 > no ip address >! >interface Vlan1 > ip address 10.12.240.205 255.255.255.0 >! >interface Vlan2 > ip address 2.2.2.2 255.255.255.0 >! >interface Vlan101 > no ip address >! >interface Vlan102 > no ip address > shutdown >! >interface Vlan105 > ip address 5.5.5.5 255.255.255.0 > ip rip send version 2 > ip rip receive version 2 >! >interface Vlan109 > ip address 9.9.9.9 255.255.255.0 >! >interface Vlan110 > ip address 48.48.48.48 255.255.255.0 >! >interface Vlan113 > ip address 13.13.13.13 255.255.255.0 >! >interface Vlan114 > ip address 14.14.14.14 255.255.255.0 > no ip redirects > no ip unreachables > ip ospf authentication message-digest > ip ospf message-digest-key 1 md5 xxx >! >interface Vlan115 > ip address 15.15.15.15 255.0.0.0 > ip rip send version 2 > ip rip receive version 2 >! >interface Vlan116 > ip address 16.16.16.16 255.255.255.0 >! >interface Vlan117 > ip address 17.17.17.17 255.255.255.0 >! >interface Vlan120 > no ip address >! >interface Vlan121 > ip address 21.21.21.21 255.255.255.0 > ip rip send version 1 > ip rip receive version 1 >! >interface Vlan121.21 >! >interface Vlan129 > ip address 29.29.29.29 255.255.255.0 > ip rip send version 1 2 > ip rip receive version 1 2 >! >interface Vlan130 > ip address 30.30.30.30 255.255.255.0 >! >interface Vlan133 > ip address 33.33.33.33 255.255.255.0 >! >interface Vlan147 > ip address 97.97.97.25 255.255.255.0 >! >interface Vlan1143 > no ip address > shutdown >! >interface Vlan1213 > no ip address > shutdown >! >router ospf 117 > router-id 205.0.0.117 > log-adjacency-changes > redistribute ospf 133 subnets > network 17.17.17.0 0.0.0.255 area 117 >! >router ospf 133 > log-adjacency-changes > network 33.33.33.0 0.0.0.255 area 133 >! >router ospf 113 > router-id 205.0.0.113 > log-adjacency-changes >! >router rip > redistribute connected > redistribute static > network 1.0.0.0 > network 5.0.0.0 > network 15.0.0.0 > network 18.0.0.0 > network 21.0.0.0 > network 29.0.0.0 > network 32.0.0.0 > network 97.0.0.0 > neighbor 29.29.29.1 > default-metric 4 >! >ip classless >ip route 36.29.29.0 255.255.255.0 29.29.29.31 8 >ip route 169.0.0.0 255.0.0.0 14.14.14.66 >ip http server >! >! >! >! >line con 0 > exec-timeout 0 0 > password smart > login local >line vty 0 4 > privilege level 0 > password smart > login local >line vty 5 > privilege level 0 > password smart > login local >line vty 6 15 > password smart > login local >! >end Если кому еще интересно, таки сам допер. В CatOS и IOS можно сконфигурировать IP. В CatOS на весь коммутатор а в IOS на порт. В CatOS set interface sc0 1(влан) 10.12.240.205/255.255.255.0 10.12.240.255 В IOS interface Vlan1 > ip address 10.12.240.205 255.255.255.0 Мас адреса там разные (хотя в коммутаторе на всех портах один мас). Отсюда и проблема. Всем удачи.
		Рекомендовать в FAQ \| Cообщить модератору \| Наверх