>Все как было))) залей старый boot в bootflash, хотя по идее у
>тебя cisco должна работать не с бутовым(читай кастированным урезанным) а с
>нормальным IOS!
>
>
>sh ver
>dir flash
>dir bootflash
>show bootvar
>sh run | i boot
Router#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-P-M), Version 12.0(21)S3, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 11-Jun-02 19:04 by dchih
Image text-base: 0x60008960, data-base: 0x60F0A000
ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-P-M), Version 12.0(21)S3, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router uptime is 11 minutes
System returned to ROM by reload at 16:57:35 UTC Thu Oct 20 2005
System image file is "disk0:c7200-p-mz.120-21.S3.bin"
cisco 7206VXR (NPE400) processor with 491520K/32768K bytes of memory.
R7000 CPU at 350Mhz, Implementation 39, Rev 3.3, 256KB L2, 4096KB L3 Cache
6 slot VXR midplane, Version 2.6
Last reset from power-on
X.25 software, Version 3.0.0.
2 FastEthernet/IEEE 802.3 interface(s)
125K bytes of non-volatile configuration memory.
46976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
Router#dir flash:
%Error opening slot0:/ (Device not ready)
Router#dir bootflash
%Error opening disk0:/bootflash (File not found)
Router#show bootvar
BOOT variable = c7200-js-mz.122-15.T8.bin,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
Configuration register is 0x2102
Router#sh run | i boot
boot system flash c7200-js-mz.122-15.T8.bin
Router#sh disk0
-#- --length-- -----date/time------ path
1 6499288 Jan 28 1951 09:21:16 c7200-p-mz.120-21.S3.bin
2 18447740 Apr 28 1954 17:50:48 c7200-js-mz.122-15.T8.bin
22937600 bytes available (24952832 bytes used)
Вот собственно, хочу сначала вернуть к исходному, а потом грузить с нормально иоса.
А всё это начал проделывать из-за того, что попался такой модуль
PA-MCX-8TE1, а с ним что-то c7200-p-mz.120-21.S3.bin не захотел и новый тоже, вот что пишет
Slot 1:
Unknown (type 378) port adapter, 0 ports
Port adapter is disabled deactivated powered off
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
PCB Serial Number : JAE08030U5K
Part Number : 73-4118-04
Board Revision : B0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 64948-0
Unknown Field (type 00CB): PA-MCX-8TE1
Part Number : 800-05358-04
EEPROM format version 4
EEPROM contents (hex):
Спасибо.
Вариант для распечатки
Маршрутизаторы CISCO и др. оборудование. (Public)
(??) on 21-Окт-05, 15:58 
